- 您現在的位置：買賣IC網 > Datasheet目錄39 > DS1624S+T&R (Maxim Integrated)IC THERM/EEPROM DIG 256BYT 8SOIC Datasheet資料下載
參數資料
| 型號： | DS1624S+T&R |
| 廠商： | Maxim Integrated |
| 文件頁數： | 7/18頁 |
| 文件大?。?/td> | 424K |
| 描述： | IC THERM/EEPROM DIG 256BYT 8SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,000 |
| 功能： | 溫度計，恒溫計 |
| 傳感器類型： | 內部 |
| 感應溫度： | -55°C ~ 125°C |
| 精確度： | ±0.5°C（最小值） |
| 拓?fù)洌?/td> | EEPROM，寄存器庫 |
| 輸出類型： | 2 線串行 |
| 輸出警報： | 無 |
| 輸出風扇： | 無 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
DS1624
f 1
The configuration register is defined as follows:
CONFIGURATION/STATUS REGISTER
where:
DONE = Conversion Done bit, 1 = Conversion complete, 0 = conversion in progress.
1SHOT = One Shot Mode. If 1SHOT is 1 , the DS1624 will perform one temperature conversion upon
receipt of the Start Convert T protocol. If 1SHOT is 0 , the DS1624 continuously performs temperature
conversions. This bit is nonvolatile and the DS1624 is shipped with 1SHOT = 0.
Since the configuration register is implemented in E
2
, writes to the register require 10ms to complete.
After issuing a command to write to the configuration register, no further accesses to the DS1624 should
be made for at least 10ms.
OPERATIONMEMORY
Byte Program Mode
In this mode, the master sends addresses and one data byte to the DS1624.
Following a START condition, the device code (4-bit), the slave address (3-bit), and the R/
bit (which
is logic-low) are placed onto the bus by the master. The master then sends the Access Memory protocol.
This indicates to the addressed DS1624 that a byte with a word address will follow after it has generated
an acknowledge bit. Therefore, the next byte transmitted by the master is the word address and will be
written into the address pointer of the DS1624. After receiving the acknowledge of the DS1624, the
master device transmits the data word to be written into the addressed memory location. The DS1624
acknowledges again and the master generates a STOP condition. This initiates the internal programming
cycle of the DS1624. A repeated START condition, instead of a STOP condition, will abort the
programming operation.
During the programming cycle the DS1624 does not acknowledge any further accesses to the device until
the programming cycle is complete (no longer than 50ms.)
Page Program Mode
To program the DS1624 the master sends addresses and data to the DS1624, which is the slave. This is
done by supplying a START condition followed by the 4-bit device code, the 3-bit slave address, and the
R/
bit which is defined as a logic-low for a write. The master then sends the Access Memory protocol.
This indicates to the addressed slave that a word address will follow. The slave outputs the acknowledge
pulse to the master during the ninth clock pulse. When the word address is received by the DS1624 it is
placed in the address pointer defining which memory location is to be written. The DS1624 will generate
an acknowledge after every 8 bits received and store them consecutively in an 8-byte RAM until a STOP
condition is detected which initiates the internal programming cycle.
A repeated START condition, instead of a STOP condition, will abort the programming operation.
During the programming cycle the DS1624 does not acknowledge any further accesses to the device until
the programming cycle is complete (no longer than 50ms).
DONE
0
0
0
1
0
1
1SHOT
相關PDF資料 |
PDF描述 |
|---|---|
| DS1626S+ | IC THERMOMETER/STAT DIG 8-SOIC |
| DS1629S+T&R | IC THERM/RTC/CALENDAR DIG 8-SOIC |
| DS1631S+T&R | IC THERMOMETER DIG HI-PREC 8SOIC |
| DS1721U+T&R | IC THERMOMETER/STAT DIG HP 8USOP |
| DS1722S | IC THERMOMETER DIG 3-WIRE 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1625S | 制造商:Maxim Integrated Products 功能描述:DIGITAL THERMOMETER, 8 Pin, SOP |
| DS1626 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Precision 3-Wire Digital Thermometer and Thermostat |
| DS1626_07 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Precision 3-Wire Digital Thermometer and Thermostat |
| DS1626S | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1626S+ | 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。