- 您現在的位置：買賣IC網 > PDF目錄379179 > DS1616 Temperature and Three Input MUX’ed 8-bit Data Recorder PDF資料下載
參數資料
| 型號： | DS1616 |
| 元件分類： | 溫度傳感器 |
| 英文描述： | Temperature and Three Input MUX’ed 8-bit Data Recorder |
| 中文描述： | 溫度和三個輸入MUX\u0026#39;ed 8位數據記錄器 |
| 文件頁數： | 23/29頁 |
| 文件大小： | 194K |
| 代理商： | DS1616 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁
DS1616
23 of 29
Communication Reset (Asynchronous Mode)
When transmitting the command, parameters, or data to the DS1616, it is possible that communication
might be interrupted. For example, the user might accidentally disconnect the cable linking the device to
the host computer. To insure that communication always starts at a known state when in the
asynchronous mode, the DS1616 will reset the communication if it senses a problem. This is
accomplished via two methods. First, if during the transmission of a byte of data to the DS1616, the stop
bit is not received, communication will be reset. The lack of a valid stop bit indicates that that particular
byte of data was not received correctly. Second, if more then 10-bit times expire between the reception of
1 byte of data and the reception of the next required byte, then communication will be reset.
Automatic resetting of communication is not required when communicating in the synchronous mode.
This is because of the function of the
RST
pin. Pulling
RST
low resets the serial communication of the
DS1616.
DS1616 COMMANDS
All communication with the DS1616 is accomplished by writing a command to the device followed by
parameter byte/s if required. Table 3 illustrates the commands supported by the DS1616.
The DS1616 commands are summarized below. Note that if an invalid command is issued, no action is
taken by the device.
DS1616 COMMANDS
Table 3
COMMAND
22h
33h
44h
Specification Test
55h
FUNCTION
Write Byte
Read Page
DESCRIPTION
Write 1 byte to RTC, Control registers, and User NV RAM
Read Page
Poll status of temperature and/or ADC Data extremes
Instructs DS1616 to immediately measure the temperature (if
CS0 = 1) and/or perform an analog to digital conversion on the
ADC Channels Selected (if CS[1-3] = 1) and store the result in
the Current Temperature and/or Current ADC Channel [1-3]
register(s) when MIP = 0.
This command clears the datalog, histogram, Temperature
Alarm, ADC Channel 1 Alarm, Current Samples, Start Time
Stamp, Start Delay, and Sample Rate registers when the Clear
Enable bit (CLR) in the Control 1 register is set to a 1.
Read Data
A5h
Clear Memory
1.
Write Byte (22h)
Host Transmit:
D7
D6
0
0
0
a6
d7
d6
D5
1
a5
d5
D4
0
a4
d4
D3
0
a3
d3
D2
0
a2
d2
D1
1
a1
d1
D0
0
a0
d0
DS1616 Response: None
Note that good programming practice insists that the Clear Memory command should be issued whenever
the DS1616 is programmed to begin a new datalogging mission.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1616S | Temperature and Three Input MUX’ed 8-bit Data Recorder |
| DS1620R | Self?Heating Temperature Sensor |
| DS1621 | Digital Thermometer and Thermostat |
| DS1624 | Digital Thermometer and Memory |
| DS1626 | High-Precision 3-Wire Digital Thermometer and Thermostat |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1616K-000 | 功能描述:KIT EVAL TEMP A/D DATA RECORDER RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| DS1616S | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Temperature and Three Input MUX’ed 8-bit Data Recorder |
| DS-1616ZJ | 制造商:Hikvision USA 功能描述:Pendant Wall Mount Bracket 3.8In X 7.65In X 12.2In 制造商:HIKVISION 功能描述:PENDANT WALL MOUNT BRACKET 3.8IN X 7.65IN X 12.2IN |
| DS16177D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Bus Transceiver |
| DS16179 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。