參數資料
型號： DS1616
元件分類： 溫度傳感器
英文描述： Temperature and Three Input MUX’ed 8-bit Data Recorder
中文描述： 溫度和三個輸入MUX\u0026#39;ed 8位數據記錄器
文件頁數： 15/29頁
文件大?。?/td> 194K
代理商： DS1616
DS1616
15 of 29
TIME OF DAY ALARM BITS
Table 2
ALARM REGISTER MASK BITS (bit 7)
SECONDS
MS
MM
1
1
0
1
0
0
0
0
MINUTES
HOURS
MH
1
1
1
0
DAYS
MD
1
1
1
1
ALARM ONCE PER SECOND
ALARM WHEN SECONDS MATCH
ALARM WHEN MINUTES AND SECONDS MATCH
ALARM WHEN HOURS, MINUTES, AND
SECONDS MATCH
ALARM WHEN DAY, HOURS, MINUTES, AND
SECONDS MATCH
0
0
0
0
SPECIAL PURPOSE REGISTERS
The following description defines the operation of the special function registers of the DS1616.
CONTROL 1 REGISTER
MSb
EOSC
LSb
AIE
CLR
0
SE
RO
TLIE
THIE
EOSC
- Enable oscillator - This bit controls the state of the oscillator in battery back-up mode only.
When set to logic 0, the oscillator is active. When this bit is set to a logic 1, the oscillator is stopped and
the DS1616 is placed into a low-power standby mode with a current drain of less than 100 nanoamps at
room temperature. When Vcc is applied or when MIP =1, the oscillator is active regardless of the state of
this bit.
CLR
- Clear Enable - This bit enables the Clear Memory command. When this bit is set to a 1 and the
Clear Memory command is subsequently issued, the datalog, histogram, Temperature Alarm, Current
Samples, Start Time Stamp, Start Delay, Sample Rate register, and ADC Data Alarm are all cleared to 0.
Following the issuing of the Clear Memory command, the CLR bit is also cleared to 0. If the Clear
Enable bit is set, but a command other than the Clear Memory command is issued next, the CLR bit is
cleared to a 0 and the contents of the datalog, histogram, temperature alarms, Current Samples registers,
Start Delay, Sample Rate, and ADC Data alarm register are unchanged.
SE -
Start Enable - This bit enables the “start” function of the
ST
input. When SE is a logic 1, the
ST
input is enabled as the start pin for datalogging operation. When enabled, datalogging operation begins
when the Sample Rate register contains a non-0 value AND the
ST
pin has been held low for at least
0.5 seconds. When SE is a logic 0, writing any non-0 value to the Sample Rate register will start
datalogging operation.
Once datalog operation has been initiated, the first data sample occurs after the specified delay written to
the Start Delay register has elapsed.
RO -
Roll-Over - This bit determines whether the datalog function of the DS1616 rolls over or stops
writing data to the datalog memory in the event that the datalog memory is completely filled. If RO is set
to a 1, the datalog memory will “roll over” after all 2048 registers in the datalog memory have been used.
In other words, after the 2048
th
register is written, the following sample will be written to register 0000,
overwriting the original data. Likewise, subsequent samples will increment through the datalog registers,
overwriting their data.
相關PDF資料
PDF描述
DS1616S Temperature and Three Input MUX’ed 8-bit Data Recorder
DS1620R Self?Heating Temperature Sensor
DS1621 Digital Thermometer and Thermostat
DS1624 Digital Thermometer and Memory
DS1626 High-Precision 3-Wire Digital Thermometer and Thermostat
相關代理商/技術參數
參數描述
DS1616K-000 功能描述:KIT EVAL TEMP A/D DATA RECORDER RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
DS1616S 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Temperature and Three Input MUX’ed 8-bit Data Recorder
DS-1616ZJ 制造商:Hikvision USA 功能描述:Pendant Wall Mount Bracket 3.8In X 7.65In X 12.2In 制造商:HIKVISION 功能描述:PENDANT WALL MOUNT BRACKET 3.8IN X 7.65IN X 12.2IN
DS16177D 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Bus Transceiver
DS16179 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*