- 您現在的位置：買賣IC網 > PDF目錄379178 > DS1236A MicroManager Chip PDF資料下載
參數資料
| 型號： | DS1236A |
| 英文描述： | MicroManager Chip |
| 中文描述： | 微管理器芯片 |
| 文件頁數： | 3/20頁 |
| 文件大?。?/td> | 320K |
| 代理商： | DS1236A |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
DS1236A
3 of 20
POWER MONITOR
The DS1236A employs a band gap voltage reference and a precision comparator to monitor the 5-volt
supply (V
CC
) in microprocessor-based systems. When an out-of-tolerance condition occurs, the RST and
RST
outputs are driven to the active state. The V
CC
trip point (V
CCTP
) is set for 10% operation so that the
RST and
RST
outputs will become active as V
CC
falls below 4.5 volts (4.37 typical). The V
CCTP
for the
5% operation option (DS1236A-5) is set for 4.75 volts (4.62 typical). The RST and
RST
signals are
excellent for microprocessor reset control, as processing is stopped at the last possible moment of in-
tolerance V
CC
. On power-up, the RST and
RST
signals are held active for a minimum of 25 ms (100 ms
typical) after V
CCTP
is reached to allow the power supply and microprocessor to stabilize. Note: The
operation described above is obtained with the reset control pin (RC) connected to GND (NMOS mode).
Please review the reset control section for more information.
WATCHDOG TIMER
The DS1236A provides a watchdog timer function which forces the RST and
RST
signals to the active
state when the strobe input (
ST
) is not stimulated for a predetermined time period. This time period is 400
ms typically with a maximum timeout of 600 ms. The watchdog timeout period begins as soon as RST
and
RST
are inactive. If a high-to-low transition occurs at the
ST
input prior to timeout, the watchdog
timer is reset and begins to time out again. The
ST
input timing is shown in NO TAG. To guarantee the
watchdog timer does not time out, a high-to-low transition on
ST
must occur at or less than 100 ms
(minimum timeout) from a reset. If the watchdog timer is allowed to time out, the RST and
RST
outputs
are driven to the active state for 25 ms minimum. The
ST
input can be derived from microprocessor
address, data, and/or control signals. Under normal operating conditions, these signals would routinely
reset the watchdog timer prior to timeout. If the watchdog timer is not required, two methods have been
provided to disable it.
Permanently grounding the IN pin in the CMOS mode (RC=1) will disable the watchdog. In normal
operation with RC=1, the watchdog is disabled as soon as the IN pin is below V
TP
. With IN grounded, an
NMI
output will occur only at power-up, or when the
ST
pin is strobed. As shown in the NO TAG, a
falling edge on
ST
will generate an
NMI
when IN is below V
TP
. This allows the processor to verify that
power is between V
TP
and V
CCTP
, as an
NMI
will be returned immediately after the
ST
strobe. The
watchdog timer is not affected by the IN pin when in NMOS mode (RC=0).
If the
NMI
signal is required to monitor supply voltages, the watchdog may also be disabled by leaving
the
ST
input open. Independent of the state of the RC pin, the watchdog is also disabled as soon as V
CC
falls to V
CCTP
.
PUSHBUTTON RESET
An input pin is provided on the DS1236A for direct connection to a pushbutton. The pushbutton reset
input requires an active low signal. Internally, this input is pulled high by a 10k resistor whenever V
CC
is
greater than V
BAT
. The
PBRST
pin is also debounced and timed such that the RST and
RST
outputs are
driven to the active state for 25 ms minimum. This 25 ms delay begins as the pushbutton is released from
a low level. A typical example of the power monitor, watchdog timer, and pushbutton reset connections
are shown in NO TAG. The
PBRST
input is disabled whenever the IN pin voltage level is less than V
TP
and the reset control (RC) is tied high (CMOS mode). The
PBRST
input is also disabled whenever V
CC
is
below V
BAT
. Timing of the
PBRST
-generated RST is illustrated in Figure 1.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1238A | CAP 3.0UF 250VAC METALLIZED POLY |
| DS1245ABP-70-IND | GT 31C 1#4,2#8,14#12,14#16 SKT |
| DS1245ABP-85-IND | GT 24C 24#16 PIN PLUG |
| DS1245YP-100-IND | CAT5E PATCH CORD 10 FOOT BEIGE |
| DS1245YP-120-IND | CAT5E PATCH CORD 15 FOOT BEIGE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1236A-10 | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| DS1236A-10+ | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| DS1236A-10N | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| DS1236A-10N+ | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| DS1236A-5 | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。