- 您現在的位置：買賣IC網 > PDF目錄223667 > DRV401AIRGWRG4 (TEXAS INSTRUMENTS INC) SPECIALTY ANALOG CIRCUIT, PQCC20 PDF資料下載
參數資料
| 型號： | DRV401AIRGWRG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQCC20 |
| 封裝： | 5 X 5 MM, GREEN, PLASTIC, QFN-20 |
| 文件頁數： | 8/36頁 |
| 文件大?。?/td> | 963K |
| 代理商： | DRV401AIRGWRG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
DRV401
SBVS070B JUNE 2006 REVISED MAY 2009
www.ti.com
16
COMPENSATION DRIVER
The compensation coil driver provides the driving current
for the compensation coil. A fully differential driver stage
offers high signal voltages to overcome the wire resistance
of the coil with only +5V supply. The compensation coil is
connected between ICOMP1 and ICOMP2, both generating an
analog voltage across the coil (see Figure 3) that turns into
current from the wire resistance (and eventually from the
inductance). The compensation current represents the
primary current transformed by the turns ratio. A shunt
resistor is connected in this loop and the high-precision
difference amplifier translates the voltage from this shunt
to an output voltage.
Both compensation driver outputs provide low impedance
over a wide frequency range to insure smooth transitions
between the closed-loop compensation frequency range
and the high-frequency range, where the primary winding
directly couples the primary current into the compensation
coil at a rate set by the winding ratio.
The two compensation driver outputs are designed with
protection circuitry to handle inductive energy. However,
additional external protection diodes might be necessary
for high current sensors.
For reliable operation, a wire break in the compensation
circuit can be detected. If the feedback loop is broken, the
integrating filter drives the outputs ICOMP1 and ICOMP2 to the
opposite rails. With one of these pins coming within 300mV
to ground, a comparator tests for a minimum current flowing
between ICOMP1 and ICOMP2. If this current stays below the
threshold current level for at least 100
s, the ERROR pin is
asserted active (low). The threshold current level for this test
is less than 57mA at 25
°C and 65mA at 40°C, if the ICOMP
pins are fully railed (see the Typical Characteristics).
For sensors with high winding resistance (compensation coil
resistance + RSHUNT) or connected to an external
compensation driver, this function should be disabled by
pulling the CCdiag pin low.
R
MAX
+
V
OUT
65mA
Where:
VOUT equals the peak voltage between ICOMP1 and ICOMP2
at a 65mA drive current.
RMAX equals the sum of the coil and the shunt resistance.
EXTERNAL COMPENSATION COIL DRIVER
An external driver for the compensation coil can be
connected to the ICOMP1 and ICOMP2 outputs. To prevent a
wire break indication, CCdiag has to be asserted low.
An external driver can provide both a higher drive voltage
and more drive current. It also moves the power
dissipation to the external transistors, thereby allowing a
higher winding resistance in the compensation coil and
more current. Figure 4 shows a block diagram of an
external compensation coil driver. To drive the buffer,
either one or both ICOMP outputs can be used. Note,
however, that the additional voltage gain could cause
instability of the loop. Therefore, the internal gain can be
reduced by approximately 8dB by asserting the GAIN pin
high. RSHUNT is connected to GND to allow for a
single-ended
external
compensation
driver.
The
differential amplifier can continue to sense the voltage,
and used for the gain and over-range comparator or
ERROR flag.
DRV401
External
Buffer
V+
V
Compensation
Coil
R
SHUNT
I
COMP1
I
COMP2
Figure 4. DRV401 with External Compensation Coil Driver and RSHUNT Connected to GND
(1)
相關PDF資料 |
PDF描述 |
|---|---|
| DS-11802D4-124 | DIGITAL TO SYNCHRO OR RESOLVER, CDIP28 |
| DS1667S-10 | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| DS1832N | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8 |
| DS2720CU/T&R | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| DS36F95J | EIA-485/EIA-422A Differential Bus Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DRV401AIRGWT | 功能描述:功率驅動器IC Sensor Sig Conditioning RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| DRV401AIRGWTG4 | 功能描述:功率驅動器IC Sensor Signal Conditioning RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| DRV401AMDWPREP | 功能描述:功率驅動器IC Enh Prod Sensor Sig Conditioning RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| DRV401-EP | 制造商:TI 制造商全稱:Texas Instruments 功能描述:SENSOR SIGNAL CONDITIONING IC FOR CLOSED-LOOP MAGNETIC CURRENT SENSOR |
| DRV401-EP_09 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:SENSOR SIGNAL CONDITIONING IC FOR SENSOR SIGNAL CONDITIONING IC FOR |
發布緊急采購，3分鐘左右您將得到回復。