- 您現在的位置：買賣IC網 > PDF目錄376727 > DK1241A (Electronic Theatre Controls, Inc.) Advanced Microstepping Motion Control Chipset PDF資料下載
參數資料
| 型號： | DK1241A |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Advanced Microstepping Motion Control Chipset |
| 中文描述： | 高級微步運動控制芯片組 |
| 文件頁數： | 19/60頁 |
| 文件大?。?/td> | 422K |
| 代理商： | DK1241A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
19
The profile mode may be programmed independently for each axis. For
example axis #1 may be in trapezoidal point to point mode while axis
#2 is in S-curve point to point.
Generally, the axis should be at rest when switching profile modes.
Under certain conditions however, switching into certain profile modes
"on-the-fly" is allowed. See specific profile descriptions for details.
S-curve Point to Point
The following table summarizes the host specified profile parameters
for the S-curve point to point profile mode:
Profile
Parameter
Destination
Position
Maximum
Velocity
Max. Accel.
Representation & Range
Units
signed 32 bits
-1,073,741,824 to 1,073,741,823
unsigned 32 bits*(1/216 scaling)
0 to 1,073,741,823
unsigned 16 bits **(1/216 scaling)
0 to 32,767
unsigned 32 bits ***(1/232 scaling)
0 to 2,147,483,647
usteps
usteps/cycle
usteps/cycle2
Jerk
usteps/cycle3
*uses 1/216 scaling. Chipset expects a 32 bit number which
has been scaled by a factor of 65,536 fromunits of
usteps/cycle. For example to specify a velocity of 2.75
usteps/cycle, 2.75 is multiplied by 65,536 and the result is
sent to the chipset as a 32 bit integer (180,224 dec. or 2c000
hex.).
**uses 1/216 scaling. Chipset expects a 16 bit number which
has been scaled by a factor of 65,536 fromunits of
usteps/cycle2. For example to specify an acceleration of .175
usteps/cycle2, .175 is multiplied by 65,536 and the result is
sent to the chipset as a 16 bit integer (11,469 dec. or 2ccd
hex).
***uses 1/232 scaling. Chipset expects a 32 bit number which
has been scaled by a factor of 4,294,967,296 (232) fromunits
of usteps/cycle3. For example to specify a jerk value of .0075
usteps/cycle3, .0075 is multiplied by 4,294,967,296 and the
result is sent to the chipset as a 32 bit integer (32,212,256
dec. or 1eb8520 hex).
Use the following figure showing a typical S-curve velocity vs. time
graph for reference in reading the next section:
Phase
I.
Phase
II.
Phase
III.
Phase
V.
Phase
VI.
Phase
VII.
Phase
IV.
S-curve profile
The S-curve profile drives the axis at the specified jerk until the
maximumacceleration is reached. (phase I). it will then drive the axis at
jerk = 0 (constant acceleration) through phase II. It will then drive the
axis at the negative of the specified jerk though phase III, such that the
axis reaches the specified maximumvelocity with acceleration = 0. This
completes the acceleration phase. At the end of the acceleration phase
of the move, the velocity will be constant, and the acceleration will be 0.
At the appropriate time, the profile will then decelerate (phases V, VI
and VII) symmetrically to the acceleration phase such that it arrives at
the destination position with acceleration and velocity = 0.
There are several conditions where the actual velocity graph of an S-
curve motion will not contain all of the segments shown in the above
figure. For example, if the max. acceleration is not reached before the
"half-way" point to the max. velocity, then the actual velocity profile will
not contain a phase II or a phase VI segment (they will have a duration
of 0 cycles). Such a profile is shown below:
Phase
I.
Phase
III.
Phase
V.
Phase
VII.
Phase
IV.
S-curve that doesn't reach max. acceleration
Another such condition is if the position is specified such that max.
velocity is not reached. In this case there will be no phase IV, and there
may also be no phase II and VI, depending on where the profile is
"truncated".
While the S-curve profile is in motion, the user is not allowed to
change any of the profile parameters. The axis must be at rest
before a new set of profile parameters can be executed. If
parameters are changed during motion then a 'command error'
相關PDF資料 |
PDF描述 |
|---|---|
| DK2100 | Navigator Motion Processor |
| DK3300 | Turbo uPSD DK3300 User Manual(Turbo系列 uPSD DK3300 用戶手冊) |
| DK60 | DIODY PROSTOWNICZE |
| DK61 | DIODY PROSTOWNICZE |
| DK62 | DIODY PROSTOWNICZE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DK125950 | 制造商:TE Connectivity 功能描述: |
| DK-125M-1 | 制造商:Luminus Devices 功能描述:EVAL BOARD & HEAT SINK FOR PT85/CBT85. MAX16818, 25A, 1 CH - Bulk |
| DK12GY | 功能描述:電氣外殼 RoHS:否 制造商:Bud Industries 產品:Wall Mount Enclosures 類型:Single Door NEMA 額定值:3R 外部深度:254 mm 外部高度:305 mm 外部寬度:305 mm 面板寬度:261 mm 面板高度:261 mm 材料:Steel 顏色:Gray 通風:Not Available |
| DK12LG | 功能描述:電氣外殼 RoHS:否 制造商:Bud Industries 產品:Wall Mount Enclosures 類型:Single Door NEMA 額定值:3R 外部深度:254 mm 外部高度:305 mm 外部寬度:305 mm 面板寬度:261 mm 面板高度:261 mm 材料:Steel 顏色:Gray 通風:Not Available |
| DK12S16 | 功能描述:電氣外殼 RoHS:否 制造商:Bud Industries 產品:Wall Mount Enclosures 類型:Single Door NEMA 額定值:3R 外部深度:254 mm 外部高度:305 mm 外部寬度:305 mm 面板寬度:261 mm 面板高度:261 mm 材料:Steel 顏色:Gray 通風:Not Available |
發布緊急采購，3分鐘左右您將得到回復。