- 您現在的位置：買賣IC網 > PDF目錄16542 > DC1786A (Linear Technology)BOARD DEMO LTC2871 PDF資料下載
參數資料
| 型號： | DC1786A |
| 廠商： | Linear Technology |
| 文件頁數： | 15/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD DEMO LTC2871 |
| 設計資源： | DC1786A Design Files DC1786A Schematic |
| 標準包裝： | 1 |
| 主要目的： | 接口，收發器，RS-232/RS-485 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | LTC2871 |
| 主要屬性： | 3 個驅動器，3 個接收器 |
| 次要屬性： | 3 V ~ 5.5 V 電源 |
| 已供物品： | 板 |
| 相關產品： | LTC2871CUHF#PBF-ND - IC TXRX RS485/RS422 38-QFN LTC2871IUHF#PBF-ND - IC TXRX RS485/RS422 38-QFN LTC2871CFE#PBF-ND - IC TXRX RS485/RS422 38-TSSOP LTC2871IFE#PBF-ND - IC TXRX RS485/RS422 38-TSSOP LTC2871CUHF#TRPBF-ND - IC TXRX RS485/RS422 38-QFN LTC2871IFE#TRPBF-ND - IC TXRX RS485/RS422 38-TSSOP LTC2871IUHF#TRPBF-ND - IC TXRX RS485/RS422 38-QFN LTC2871CFE#TRPBF-ND - IC TXRX RS485/RS422 38-TSSOP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
LTC2870/LTC2871
22
28701f
APPLICATIONS INFORMATION
Receiver Outputs
The RS232 and RS485 receiver outputs are internally
driven high (to VL) or low (to GND) with no external pull-
up needed. When the receivers are disabled the output pin
becomes Hi-Z with leakage of less than ±5μA for voltages
within the VL supply range.
RS485 Receiver Input Resistance
The RS485 receiver input resistance from A or B to GND
(Y or Z to GND in half-duplex mode with driver disabled) is
greater than 96kΩ (typically 125kΩ) when the integrated
termination is disabled. This permits up to a total of 256
receivers per system without exceeding the RS485 receiver
loading specification. The input resistance of the receiver
is unaffected by enabling/disabling the receiver or whether
the part is in half-duplex, full-duplex, loopback mode, or
even unpowered. The equivalent input resistance looking
into the RS485 receiver pins is shown in Figure 17.
Figure 18. Typical Resistance of the Enabled RS485
Terminator vs Common Mode Voltage on A /B
through logic control, the proper line termination for cor-
rect operation when configuring transceiver networks.
Termination should be enabled on transceivers positioned
at both ends of the network bus. Termination on the driver
nodes is important for cases where the driver is disabled
but there is communication on the connecting bus from
another node. Differential termination resistors are never
enabled in RS232 mode on the LTC2870.
When the TE485 pin is high, the termination resistors are
enabled and the differential resistance from A to B and Y
to Z is 120Ω. The resistance is maintained over the entire
RS485 common mode range of –7V to 12V as shown in
Figure 18.
Figure 17: Equivalent RS485 Receiver
Input Resistance Into A and B (Note 5)
28701 F17
A
B
TE485
60Ω
125k
Selectable RS485 Termination
Proper cable termination is important for good signal fidel-
ity. When the cable is not terminated with its characteristic
impedance, reflections cause waveform distortion.
The LTC2870 and LTC2871 offer integrated switchable
120Ω termination resistors between the differential receiver
inputs and also between the differential driver outputs.
This provides the advantage of being able to easily change,
RS485 Half- and Full-Duplex Control
The LTC2870 and LTC2871 are equipped with a control to
switch between half- and full-duplex operation. With the
H/F pin set to a logic low, the A and B pins serve as the
differential receiver inputs. With the H/F pin set to a logic
high, the Y and Z pins serve as the differential inputs. In
either configuration, the RS485 driver outputs are always
on Y and Z. The impedance looking into the A and B pins
is not affected by H/F control, including the differential
termination resistance. The H/F control does not affect
RS232 operation.
VOLTAGE (V)
–10
RESIST
ANCE
(Ω)
126
124
122
118
120
116
10
–5
28701 F18
15
5
0
VCC = 5.0V
VCC = 3.3V
相關PDF資料 |
PDF描述 |
|---|---|
| GCM24DCCS-S189 | CONN EDGECARD 48POS R/A .156 SLD |
| 6278016-3 | CABLE ASSY SC-SC DUPLEX MM 3M |
| 5503995-2 | CABLE ASSEM FIBER ST-ST 2 METER |
| ECO-S1HA152BA | CAP ALUM 1500UF 50V 20% SNAP |
| EEU-FR1J821 | CAP ALUM 820UF 63V 20% RADIAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DC1788A-B | 制造商:Linear Technology 功能描述:EVAL BOARD, LT4275B POE & PD CONTROLLER, Silicon Manufacturer:Linear Technology, |
| DC1788A-C | 制造商:Linear Technology 功能描述:EVAL BOARD, LT4275C POE & PD CONTROLLER, Silicon Manufacturer:Linear Technology, |
| DC1788B-A | 制造商:Linear Technology 功能描述:EVAL BOARD FOR LT4275 90W 制造商:Linear Technology 功能描述:LT4275 POWERED DEVICE CTRL EVAL BOARD 制造商:Linear Technology 功能描述:DEMO BOARD, LT4275, POWER OVER ETHERNET CONTROLLER, Silicon Manufacturer:Linear |
| DC178A | 功能描述:BOARD SAR ADC LTC1418 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| DC1792 | 功能描述:BOARD DAC LTC2756 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:QuikEval™, SoftSpan™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
發布緊急采購，3分鐘左右您將得到回復。