- 您現在的位置：買賣IC網 > PDF目錄19022 > DC1620A-G (Linear Technology)BOARD DEMO 125MSPS LTC2145-14 PDF資料下載
參數資料
| 型號： | DC1620A-G |
| 廠商： | Linear Technology |
| 文件頁數： | 6/38頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD DEMO 125MSPS LTC2145-14 |
| 軟件下載： | QuikEval II System |
| 設計資源： | DC1620A Design Files DC1620A Schematic |
| 標準包裝： | 1 |
| 系列： | * |
| 相關產品： | DC890B-ND - BOARD USB DATA COLLECTION |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
LTC2145-14/
LTC2144-14/LTC2143-14
14
21454314fa
PINS THAT ARE THE SAME FOR ALL DIGITAL
OUTPUT MODES
VDD (Pins 1, 16, 17, 64): Analog Power Supply, 1.7V to
1.9V. Bypass to ground with 0.1μF ceramic capacitors.
Adjacent pins can share a bypass capacitor.
VCM1 (Pin 2):Common Mode Bias Output, Nominally Equal
to VDD/2. VCM1 should be used to bias the common mode
of the analog inputs to channel 1. Bypass to ground with
a 0.1μF ceramic capacitor.
GND (Pins 3, 6, 14): ADC Power Ground.
AIN1+ (Pin 4): Channel 1 Positive Differential Analog Input.
AIN1– (Pin 5): Channel 1 Negative Differential Analog Input.
REFH (Pins 7, 9): ADC High Reference. See the Applica-
tions Information section for recommended bypassing
circuits for REFH and REFL.
REFL (Pins 8, 10): ADC Low Reference. See the Applica-
tions Information section for recommended bypassing
circuits for REFH and REFL.
PAR/SER (Pin 11): Programming Mode Selection Pin.
Connect to ground to enable the serial programming mode.
CS, SCK, SDI, SDO become a serial interface that control
the A/D operating modes. Connect to VDD to enable the
parallel programming mode where CS, SCK, SDI, SDO
become parallel logic inputs that control a reduced set of
the A/D operating modes. PAR/SER should be connected
directly to ground or VDD and not be driven by a logic signal.
AIN2+(Pin12):Channel2PositiveDifferentialAnalogInput.
AIN2–(Pin13):Channel2NegativeDifferentialAnalogInput.
VCM2 (Pin 15): Common Mode Bias Output, Nominally
Equal to VDD/2. VCM2 should be used to bias the common
mode of the analog inputs to channel 2. Bypass to ground
with a 0.1μF ceramic capacitor.
ENC+ (Pin 18):
Encode Input. Conversion starts on the
rising edge.
ENC– (Pin 19):
Encode Complement Input. Conversion
starts on the falling edge. Tie to GND for single-ended
encode mode.
CS (Pin 20): In Serial Programming Mode, (PAR/SER =
0V), CS Is the Serial Interface Chip Select Input. When
CS is low, SCK is enabled for shifting data on SDI into the
mode control registers. In the parallel programming mode
(PAR/SER = VDD),CScontrolstheclockdutycyclestabilizer
(See Table 2). CS can be driven with 1.8V to 3.3V logic.
SCK (Pin 21): In Serial Programming Mode, (PAR/SER =
0V), SCK Is the Serial Interface Clock Input. In the parallel
programming mode (PAR/SER = VDD), SCK controls the
digital output mode (see Table 2). SCK can be driven with
1.8V to 3.3V logic.
SDI (Pin 22): In Serial Programming Mode, (PAR/SER =
0V), SDI Is the Serial Interface Data Input. Data on SDI
is clocked into the mode control registers on the rising
edge of SCK. In the parallel programming mode (PAR/
SER = VDD), SDI can be used together with SDO to power
down the part (see Table 2). SDI can be driven with 1.8V
to 3.3V logic.
OGND (Pin 41): Output Driver Ground. Must be shorted
to the ground plane by a very low inductance path. Use
multiple vias close to the pin.
OVDD (Pin 42): Output Driver Supply. Bypass to ground
with a 0.1μF ceramic capacitor.
SDO (Pin 61): In Serial Programming Mode, (PAR/SER
= 0V), SDO Is the Optional Serial Interface Data Output.
Data on SDO is read back from the mode control regis-
ters and can be latched on the falling edge of SCK. SDO
is an open-drain NMOS output that requires an external
2k pull-up resistor to 1.8V – 3.3V. If read back from the
mode control registers is not needed, the pull-up resistor
is not necessary and SDO can be left unconnected. In the
parallel programming mode (PAR/SER = VDD), SDO can
be used together with SDI to power down the part (see
Table 2). When used as an input, SDO can be driven with
1.8V to 3.3V logic through a 1k series resistor.
VREF (Pin 62): Reference Voltage Output. Bypass to
ground with a 2.2μF ceramic capacitor. The output voltage
is nominally 1.25V.
PIN FUNCTIONS
相關PDF資料 |
PDF描述 |
|---|---|
| 32 | LAMP INCAND T-1 12V SUB MIDGET |
| 8-2417T | T-1 12V .100" BI-PIN BASE |
| 7355 | LAMP INCAND T1-3/4 MIDGE GROOVE |
| A0215Y | 30MM IND CTRL PB OPERATOR |
| DC1370A-L | BOARD DEMO 25MSPS LTC2256-12 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DC1620A-H | 功能描述:BOARD DEMO 105MSPS LTC2144-14 RoHS:是 類別:未定義的類別 >> 其它 系列:* 標準包裝:1 系列:* 其它名稱:MS305720A |
| DC1620A-I | 功能描述:BOARD DEMO 80MSPS LTC2143-14 RoHS:是 類別:未定義的類別 >> 其它 系列:* 標準包裝:1 系列:* 其它名稱:MS305720A |
| DC1620A-J | 功能描述:BOARD DEMO 65MSPS LTC2142-14 RoHS:是 類別:未定義的類別 >> 其它 系列:* 標準包裝:1 系列:* 其它名稱:MS305720A |
| DC1620A-K | 功能描述:BOARD DEMO 40MSPS LTC2141-14 RoHS:是 類別:未定義的類別 >> 其它 系列:* 標準包裝:1 系列:* 其它名稱:MS305720A |
| DC1620A-L | 功能描述:BOARD DEMO 25MSPS LTC2140-14 RoHS:是 類別:未定義的類別 >> 其它 系列:* 標準包裝:1 系列:* 其它名稱:MS305720A |
發布緊急采購，3分鐘左右您將得到回復。