- 您現在的位置：買賣IC網 > PDF目錄376564 > DAC8541EVM (Texas Instruments, Inc.) DAC8541EVM(DAC8541評估板) PDF資料下載
參數資料
| 型號： | DAC8541EVM |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | DAC8541EVM(DAC8541評估板) |
| 中文描述： | DAC8541EVM（DAC8541評估板） |
| 文件頁數： | 22/26頁 |
| 文件大小： | 351K |
| 代理商： | DAC8541EVM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁
Host Processor Operation
3-4
Table 3-4.Capacitive Load Drive Output Jumper Settings
Reference
Jumper Position
Function
W3
2-3
Negative rail of the op amp tied to analog GND
W4
1-2
Positive rail supply of the op amp tied to 15 V
W5
3-4
Capacitive load drive output of DAC is channeled to the output terminals
W6
Open
Disconnect V
REF(H)
from negative input of op amp
Disconnect R8 (see Note)
W7
Open
Note:
If there is a need to incrementally adjust the capacitive load output, replace R8 with a capacitor with the desired capaci-
tance value and CLOSE W7.
3.2.4
Bipolar Operation Using the DAC8541 (Default Mode)
Although the DAC8541 is designed for single-supply operation, the bipolar
output of operation is implemented using the circuit shown in Figure 3-1. The
output of the circuit gives an output voltage range of
±
V
REF(H)
. The rail-to-rail
operation at the amplifier output is achievable using an OPA627 as the output
amplifier.
Figure 3-1. Bipolar Operation With the DAC8541
_
+
OPA627
15 V
-15 V
R2
10 k
V
OUT
SENSE
V
OUT
DAC8541
V
REF
H
V
REF
L
±
5 V
R1
10 k
0.1
μ
F
10
μ
F
V
REF
U2
U1
The bipolar configuration is accomplished by following the correct jumper
settings according to Table 3-5.
Table 3-5.Bipolar Operation Output Jumper Settings
Reference
Jumper Position
Function
W3
1-2
Negative rail supply of the op amp tied to -15 V
W4
1-2
Positive rail supply of the op amp tied to 15 V
W5
Close
Bipolar output of DAC is channeled to the output terminals
W6
Close
Connect V
REF(H)
to the negative input of op amp for negative biasing
Disconnect R8
W7
Open
An example in Figure 3-2 shows the sinusoidal signal in channel 1 being
amplified within the range of
±
V
REF(H)
shown in channel 2. The reference
voltage, V
REF(H)
, is set to 5 V, which is then supplied to the negative input of
U2 to bias the circuit to its negative rail. This provides an output of
±
5 V with
相關PDF資料 |
PDF描述 |
|---|---|
| DAC8544I | QUAD, 16-BIT, RAIL-TO-RAIL VOLTAGE OUTPUT, PARALLEL INTERFACE, DIGITAL-TO-ANALOG CONVERTER |
| DAC8551IDGK | 16-BIT, ULTRA-LOW GLITCH, VOLTAGE OUTPUT DIGITAL-TO-ANALOG CONVERTER |
| DAC8551IDRBR | 16-BIT, ULTRA-LOW GLITCH, VOLTAGE OUTPUT DIGITAL-TO-ANALOG CONVERTER |
| DAC8551IDRBT | 16-BIT, ULTRA-LOW GLITCH, VOLTAGE OUTPUT DIGITAL-TO-ANALOG CONVERTER |
| DAC8562ER | 12-Bit Digital-to-Analog Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DAC8541Y | 制造商:Texas Instruments 功能描述:IC 16BIT DAC SMD 8541 TQFP32 |
| DAC8541Y | 制造商:Texas Instruments 功能描述:IC 16BIT DAC SMD 8541 TQFP32 |
| DAC8541Y/250 | 功能描述:數模轉換器- DAC Low Power 16-Bit DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC8541Y/250G4 | 功能描述:數模轉換器- DAC Low Power 16-Bit DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC8541Y/2K | 功能描述:數模轉換器- DAC Low Power 16-Bit DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。