- 您現在的位置：買賣IC網 > PDF目錄2067 > D2-45157-QR (Intersil)IC DGTL AMP PWM CTRLR 68QFN PDF資料下載
參數資料
| 型號： | D2-45157-QR |
| 廠商： | Intersil |
| 文件頁數： | 19/31頁 |
| 文件大小： | 0K |
| 描述： | IC DGTL AMP PWM CTRLR 68QFN |
| 標準包裝： | 30 |
| 系列： | D2Audio™ |
| 類型： | D 類 |
| 輸出類型： | 2 通道（立體聲） |
| 在某負載時最大輸出功率 x 通道數量： | 30W x 2 @ 8 歐姆 |
| 電源電壓： | 9 V ~ 26 V |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 68-QFN 裸露焊盤（10x10） |
| 封裝/外殼： | 68-VFQFN 裸露焊盤 |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
D2-45057, D2-45157
26
FN6785.0
July 29, 2010
Protection
The D2-45057, D2-45157 device includes multiple
protection mechanisms. Output overload and overcurrent
status for each output power stage provides two levels of
monitoring. Temperature monitoring provides two levels
of temperature status. On-chip undervoltage detection is
included for all supply voltages.
Several strategies are provided in the D2-45057,
D2-45157 to prevent damage from the high voltages,
currents, and temperatures present in class-D amplifiers.
This protection is also effective against user-induced
faults such as clipping, output overload, or output shorts,
including both shorted outputs or short-to-ground faults.
Protection includes events such as:
Output Overcurrent
Output Short Circuit
Over-Temperature
Power Supply Brown-Out
Shoot-Through Overcurrent
Certain levels of protection are managed using on-chip
hardware. Other protection is integrated into device
firmware, and involves actions to:
Shut down the outputs for a short circuit,
over-temperature, or undervoltage event.
Shut down the device if power supply sensors detect
voltages dropping below their design thresholds.
Providing both indication, and device shutdown if
needed for overload and overcurrent monitors
detection. Dual threshold monitors provide two
levels of high current conditions.
Chip temperature monitoring provides dual threshold
status of high temperature conditions, providing
both indication, and device shutdown if needed.
Error Reporting
Internal monitoring of system and device operation uses
an I/O pin (nERROR/CFG1) as an output to signal an
external system controller of a channel shutdown error
condition. This output may be used to turn on a simple
indicator.
The error output is also used to signal an external
microcontroller that the I2C bus may be busy. When the
error output is low during system initialization, the I2C
bus is busy as a master device.
This error output is active low and only becomes used as
an error reporting output after the device firmware has
initialized and began running. This same pin is shared as
description on shared-function pins.) During a reset
condition, this pin operates as an input, and is one of two
input pins that are used to define the configuration
mode. A resistor pull-up or pull-down on this pin
establishes this mode input configuration state. After
completion of the initialization sequence, these resistors
do not affect the error output operation.
Short-Circuit and Overcurrent Sensing
Each PWM output FET includes a dual-threshold
overcurrent sensor. Multiple functions occur depending
on detection of overcurrent conditions:
The lower threshold is used to monitor fault
conditions such as shorts or overloads on the
loudspeaker outputs.
The higher threshold monitors fault conditions of the
PWM output pin.
The nERROR output asserts for the channel detecting
the fault.
For the lower level threshold, nERROR remains
asserted only through the duration of the
overcurrent event.
For the higher level threshold, the output is shut
down, and its nERROR output is asserted, and these
remain latched until the controller acknowledges the
fault event by turning off the channel’s PWM drive.
(When shutdown, the PWM output pin floats.)
Hysteresis is built into the overcurrent detectors to
suppress PWM switching transient events.
Protection Monitoring and Control
These overcurrent detectors generate either a pulse or
latched logic level (depending on low or high threshold)
upon detection of high current. Detector status is
presented to the nERROR[0:3] pins.
The PROTECT[0:2] pins are used as protection inputs to
the firmware. Firmware action based on these pins’
status depends on the selected output mode
configuration. The nERROR[0:3] output pins and the
PROTECT[0:2] input pins are connected together based
on the particular system and output mode configuration,
Thermal Protection and Monitors
An temperature sensing provides two thresholds of
temperature monitoring.
If the device reaches the lower threshold, a warning
indication is generated, and triggers one level of thermal
protection management.
On-chip hardware thermal protection shuts down the
device upon a high-threshold temperature condition. If
the device reaches the higher threshold, on-chip
hardware latches and shuts down all four output stages.
It also drives all four nERROR0-3 outputs low (active)
providing this shut-down status to the firmware through
their connected PROTECT0-2 inputs.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1080CLU+ | IC CRYSTAL MULTIPLIER SS 8-MSOP |
| DS1080LU+A00 | IC CRYSTAL MULT SS 8-USOP |
| DS1085LZ-12+ | IC ECONOSCILLATOR SYNTH 8-SOIC |
| DS1085Z-25+ | IC ECONOSCILLATOR SYNTH 8-SOIC |
| DS1086HU-C02+ | IC ECONOSCILLATOR SS 8-USOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| D2-45157-QR-T | 功能描述:音頻 DSP DAE-4P MULTI-DIE LW- PWR CLASS-AMPLIFIER RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube |
| D245-5 | 制造商:KLEIN TOOLS 功能描述:Plier, Diagonal-Cutting; Tapered; 5-1/16 in.; 11/16 in.; 9/16 in.; 3/8 in.; Red 制造商:Klein Tools Inc 功能描述:TOOLS PLIERS 制造商:KLEIN TOOLS 功能描述:TOOLS, PLIERS; Plier Style:Diagonal Cutting; Jaw Length:18mm; Overall Length:129mm; Features:Tapered nose gets in confined areas; ideal for close-tip cutting; Handle Color:Red ;RoHS Compliant: NA 制造商:Klein Tools Inc 功能描述:Standard Diagonal Cutting Pliers |
| D245-5C | 制造商:Klein Tools Inc 功能描述: |
| D246 | 制造商:PETERMANN 制造商全稱:PETERMANN 功能描述:HIGH RELIABILITY FOR LOW COST |
| D24-6 | 制造商:RICHARD MANNO 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。