Specifications and information are subject to change without notice
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: sales@wj.com
Web site: www.wj.com
Page 1 of 5 May 2006
CV111-3A
UMTS-band High Linearity Downconverter
Product Information
The Communications Edge
TM
Product Features
High dynamic range downconverter
with integrated LO, IF, & RF amps
RF: 1900 – 2200 MHz
IF: 65 – 300 MHz
+38 dBm Output IP3
+21 dBm Output P1dB
5.3 dB Noise Figure
+5V Single supply operation
Pb-free 6mm 28-pin QFN package
Low-side LO configuration
Common footprint with other
PCS/ cellular versions
Product Description
The CV111-3A is a high linearity downconverter
designed to meet the demanding issues for performance,
functionality, and cost goals of current and next
generation mobile infrastructure basestations. It provides
high dynamic range performance in a low profile
surface-mount leadless package that measures 6 x 6 mm
square.
Functionality includes RF amplification, frequency
conversion and IF amplification, while an integrated LO
driver amplifier powers the passive mixer. The MCM is
implemented with reliable and mature GaAs MESFET
and InGaP HBT technology.
Typical applications include frequency down conversion,
modulation and demodulation for receivers used in
CDMA, CDMA2000, W-CDMA / IMT2000, GPRS, and
EDGE 2.5G mobile infrastructure technologies for
UMTS frequency bands.
Functional Diagram
Top View
Specifications
(1)
Parameters
RF Frequency Range
LO Frequency Range
IF Center Frequency Range
% Bandwidth around IF center frequency
IF Test Frequency
SSB Conversion Gain
Gain Drift over Temp (-40 to 85 °C)
Output IP3
Output IP2
Output 1dB Compression Point
Noise Figure
LO Input Drive Level
LO-RF Isolation
LO-IF Isolation
Return Loss: RF Port
Return Loss: LO Port
Return Loss: IF Port
Operating Supply Voltage
Supply Current
FIT Rating
Junction Temperature
Units
MHz
MHz
MHz
%
MHz
dB
dB
dBm
dBm
dBm
dB
dBm
dB
dB
dB
dB
dB
V
mA
failures
/
1E9 hrs
°
C
Min
Typ
Max
Comments
See note 2
See note 3
Temp = 25 °C
Referenced to +25 °C
See note 4
See note 4
See note 5
P
LO
= 0 dBm
P
LO
= 0 dBm
@ 70
o
C ambient, 90% confidence
See note 6
1900 – 2200
1600 – 2135
65 – 300
±7.5
240
20
±0.5
+38
+48
+21
5.3
0
40
25
14
14
14
+5
360
-2.5
+4.9
290
+2.5
+5.1
480
72.1
160
1. Specifications when using the application specific circuit (shown on page 3) with a low side LO = 0 dBm in a downconverting application over the operating case temperature range.
2. IF matching components affect the center IF frequency. Proper component values for other IF center frequencies than shown can be provided by emailing to applications.engineering@wj.com.
3. The IF bandwidth of the converter is defined as 15% around any center frequency in its operating IF frequency range. The bandwidth is determined with external components. Specifications are valid around
the total ±7.5% bandwidth. ie. with a center frequency of 80 MHz, the specifications are valid from 80 ± 6 MHz.
4. Assumes the supply voltage = +5 V. OIP3 is measured with
Δ
f
= 1 MHz with IF
= 5 dBm / tone.
5. Assumes LO injection noise is filtered at the thermal noise floor, -174 dBm/Hz, at the RF, IF, and Image frequencies.
6. The maximum junction temperature ensures a minimum MTTF rating of 1 million hours of usage.
Absolute Maximum Rating
Parameter
Operating Case Temperature
Storage Temperature
DC Voltage
Junction Temperature
RF Input (continuous)
Rating
-40 to +85
°
C
-55 to +125° C
+6 V
+220 °C
+2 dBm
Operation of this device above any of these parameters may cause permanent damage.
Ordering Information
Part No.
CV111-3AF
CV111-3APCB75
CV111-3APCB240 Fully Assembled Eval. Board, IF = 240MHz
Description
UMTS-band High Linearity Downconverter
(lead-free/RoHS-compliant 6x6mm QFN package)
Fully Assembled Eval. Board, IF = 75MHz
G
28
R
27
G
26
M
25
G
24
I
23
G
22
1
2
3
4
5
6
7
21
20
19
18
17
16
15
8
G
9
10
G
11
M
12
G
13
L
14
G
IF Amp
RF Amp
LO Driver Amp
IF OUT
GND
GND
GND
BIAS
GND
LO IN
RF OUT
GND
GND
GND
GND
GND
MIXRF
G
RF
IF
LO