- 您現在的位置：買賣IC網 > PDF目錄16879 > CMOD232+ (Maxim Integrated Products)EVAL SYSTEM FOR MAX9850 PDF資料下載
參數資料
| 型號： | CMOD232+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 15/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL SYSTEM FOR MAX9850 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
MAX9850
Status Registers (0x0, 0x1)
Alert Flag (ALERT)
1 = An interrupt event has occurred.
0 = No interrupt event has occurred.
ALERT is an alert flag that sets when an interrupt event
has occurred. The events that can be programmed to
set ALERT are as follows:
A change in state on SGPIO indicating a change in
levels at GPIO when GPIO is configured as an input.
Configure GPIO as an input and set ISGPIO = 1 in
the interrupt enable register (register 0x4, bit B6).
The internal PLL locks or unlocks with LRCLK. Set
ILCK = 1 in the interrupt enable register (register
0x4, bit B5).
A change in state on SHPS indicating headphones
have been connected or disconnected. Set ISHPS =
1 in the interrupt enable register (register 0x4, bit B4).
The headphone amplifier reaches its minimum vol-
ume. Set IVMN = 1 in the interrupt enable register
(register 0x4, bit B3).
An overload on either right or left headphone out-
puts (HPR, HPL). Set IIOH = 1 in the interrupt
enable register (register 0x4, bit B0).
ALERT sets to 1 after an event occurs and remains set
until the status A register is read. GPIO configured as an
output can interrupt a C on an ALERT event. GM(1:0) in
the GPIO register (register 0x3, bits B7 and B6) control
the output mode of GPIO. See the GPIO section for more
information on programming GPIO as an output.
GPIO Status (SGPIO)
1 = GPIO is high.
0 = GPIO is low.
SGPIO reports the status of GPIO at the time that status
A is read, regardless of whether GPIO is programmed
as an input or output. A change in state on SGPIO
causes ALERT to set to 1 when GPIO is configured as
an input and ISGPIO = 1 in the interrupt enable register
(register 0x4, bit B6).
PLL Lock Status (LCK)
1 = The internal PLL is locked with LRCLK.
0 = The internal PLL is not locked with LRCLK.
LCK reports the lock status of the internal PLL at the
time that STATUS A is read. The DAC is disabled when
the PLL is not locked. When the PLL is locked with
LRCLK, the DAC will become operational if DACEN is
equal to 1 (register 0x5, bit B0). ALERT sets to 1 when
LCK changes state if ILCK = 1 in the interrupt enable
register (register 0x4, bit B5).
HPS Status (SHPS)
1 = HPS is high, indicating that headphones are con-
nected.
0 = HPS is low, indicating no headphone is connected.
SHPS reports the debounced status of HPS at the time
STATUS A is read. SHPS = 0 indicates that no head-
phone is connected and HPS is low. SHPS sets to 1 when
HPS is high, indicating headphones are connected.
ALERT sets to 1 when SHPS changes state, if ISHPS = 1
in the interrupt enable register (register 0x4, bit B4).
Volume at Minimum (VMN)
1 = Headphone volume has reached its minimum volume.
0 = Headphone volume is not at its minimum.
VMN sets to 1 when the minimum headphone amplifier
volume has been reached. ALERT sets to 1 when IVMN
= 1 in the interrupt enable register (register 0x4, bit B3).
Headphone Overcurrent Left (IOHL)
1 = The left headphone output (HPL) has experienced
an overcurrent condition.
0 = The left headphone output (HPL) is operating normally.
IOHL sets to 1, when an overcurrent occurs on the left
headphone output HPL and remains set until status A is
read. ALERT sets to 1 when an overcurrent on the right
or left headphone output occurs if IIOH = 1 in the inter-
rupt enable register (register 0x4, bit B0).
Headphone Overcurrent Right (IOHR)
1 = The right headphone output (HPR) has experi-
enced an overcurrent condition.
0 = The right headphone output (HPR) is operating normally.
IOHR sets to 1 and remains set until STATUS A is read.
ALERT sets to 1 when an overcurrent on the right or left
headphone output occurs if IIOH = 1 in the interrupt
enable register (register 0x4, bit B0).
Stereo Audio DAC with DirectDrive
Headphone Amplifier
22
______________________________________________________________________________________
Table 10. Status A (0x0) Read-Only, Bit
Descriptions
B7
B6
B5
B4
B3
B2
B1
B0
ALERT SGPIO
LCK
SHPS
VMN
1
IOHL
IOHR
相關PDF資料 |
PDF描述 |
|---|---|
| 562A011-3/86-0 | BOOT MOLDED |
| 0210391020 | CABLE JUMPER 1MM .178M 31POS |
| TCSD-10-D-04.50-01-N-R | CABLE STRIPS - SEE NOTES |
| 0982660809 | CBL 10POS 0.5MM JMPR TYPE A 1' |
| VI-J4Z-EX | CONVERTER MOD DC/DC 2V 30W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CMOD232+ | 功能描述:界面開發工具 Cmod232+ Eval Kit RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| CMOD3003 | 功能描述:二極管 - 通用，功率，開關 ULTRAMINI SURFACE MOUNT RoHS:否 制造商:STMicroelectronics 產品:Switching Diodes 峰值反向電壓:600 V 正向連續電流:200 A 最大浪涌電流:800 A 配置: 恢復時間:2000 ns 正向電壓下降:1.25 V 最大反向漏泄電流:300 uA 最大功率耗散: 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:ISOTOP 封裝:Tube |
| CMOD3003 BK | 制造商:Central Semiconductor Corp 功能描述:Diode Switching 180V 0.6A Box |
| CMOD3003 TR | 制造商:Central Semiconductor Corp 功能描述:Diodes - General Purpose, Power, Switching ULTRAMINI SURFACE MOUNT |
| CMOD3003_10 | 制造商:CENTRAL 制造商全稱:Central Semiconductor Corp 功能描述:SURFACE MOUNT LOW LEAKAGE SILICON SWITCHING DIODE |
發布緊急采購，3分鐘左右您將得到回復。