參數資料
型號: CLT3-4BT6
廠商: 意法半導體
英文描述: CURRENT LIMITED OVER-VOLTAGE PROTECTED QUAD DIGITAL TERMINATION
中文描述: 電流限制過電壓保護4個數字終止
文件頁數: 6/10頁
文件大?。?/td> 99K
代理商: CLT3-4BT6
CLT3-4BT6
6/10
CLT3-4 INPUT / OUTPUT TRANSFER CHARACTERISTICS (respect to common pin COM)
ISOLATOR ON
ISOLATOR OFF
Forbidden
Transition zone
T
0
0.5
1
1.5
2
2.5
3
3.5
4
0
0.5
1
1.5
2
2.5
3
3.5
4
0.04
2.1
3.7
I
(mA)
IN
I
(mA)
OUT
Fig. 4:
Current tranfer characteristic
0
0.5
1
1.5
2
2.5
3
3.5
4
0
5
10
15
I
20
25
30
ISOLATOR ON
I
(mA)
OUT
V (V)
Fig. 5:
Transconductance characteristic
The CLT device is used between the connector and the opto-coupler of an I/O module. To secure the
coupler off state and the non-conduction of its diode, the maximum CLT output current is 40μA with R opto
= 15k
. When the CLT input voltage V
IN
is higher than 5 V, a minimum CLT output current of 1.5 mA will
secure the opto-coupler on state.
TheCLTlimiterisinsensitivetotheoutputvoltageupto2.0V.Therefore,itsoutputisabletodriveanystate
of the art opto-coupler. Some additional device can be added in series with the opto-coupler if the output
voltage remains within its functional limits.
A stand-alone sensor is normally connected on the CLT input. For a good off state control, its quiescent
current has to be less than 1.5 mA (EN60947-5-2 standard compatible) keeping then the opto-coupler off
thanks to the CLT device (I
OUT
< 40μA). And its maximum ON state voltage V
S-ON
will be lower than 8 V
(EN60947-5-2 standard compatible) corresponding to the difference between the minimum supply voltage
(V
CC MIN
=19.2V)andthemaximumcurrentlimitationactivationvoltageV
CC MIN
=V
S-ON
+V
I
;V
I
=V
IN
+R
I
x
I
IN MAX
+ V
D
(V
I
= 11 V when V
IN
= 5 V, R
I
= 1.2 k
, I
IN
< 3.7 mA, V
D
= 1V).
APPLICATION DESCRIPTION
The input and supply pins are designed to withstand electromagnetic interferences. As shown on the
device block diagram, each channel input is protected by a clamping diode that is connected to the
common pin COM. Combined with a serial input resistance R
I
= 1.2 k
, this clamping diode implements an
effective protection against transient voltage burst (±4 kV, IEC61000-4-4) and voltage surge (±1 kV,
IEC61000-4-5).
This combination allows the surge voltage to be applied from each input to other inputs, the ground and the
supply contacts in differential or common modes (see figure 6).
Thanks to its high resistance R
C
= 4.7 k
and the conventional power supply protection that uses a
clamping diode such as the SM15T39C Transil, the supply pin V
C
withstands IEC61000-4-5 with +/-
1000 V surge voltage (see figure 7).
Finally, an external output capacitor may be placed in parallel with the opto-coupler diode to filter the
transient disturbances injected in the inputs of the module and secure the immunity of the opto-coupler
itself.
SURGE VOLTAGE TEST CIRCUIT
相關PDF資料
PDF描述
CM-1H8 Miniature High Level Double Balanced Mixer 5-500 MHz
CM17699 COLOR PDP DRIVER MODULE
CMBA847 NPN EPITAXIAL PLANAR SILICON TRANSISTOR
CMBA857 PNP EPITAXIAL PLANAR SILICON TRANSISTOR
CMBD226 SILICON PLANAR DUAL SWITCHING DIODE
相關代理商/技術參數
參數描述
CLT3-4BT6-TR 功能描述:接口 - 專用 Quad Digital Term RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
CLT35F-7M20 功能描述:非熱縮管和套管 Corr. Loom Tubing Slit, .31" (7.9mm) X 7 RoHS:否 制造商:Panduit 產品:Cable Wraps 類型:Spiral 顏色:Black 材料:PP 內徑:0.03 in 長度:100 ft
CLT35F-C20 功能描述:非熱縮管和套管 Corr. Loom Tub Slit .31" (7.9mm) 100ft RoHS:否 制造商:Panduit 產品:Cable Wraps 類型:Spiral 顏色:Black 材料:PP 內徑:0.03 in 長度:100 ft
CLT35F-C3 功能描述:非熱縮管和套管 Corr Loom Tubng Slit 5/16" 100’ ORNG POLY RoHS:否 制造商:Panduit 產品:Cable Wraps 類型:Spiral 顏色:Black 材料:PP 內徑:0.03 in 長度:100 ft
CLT35F-C4 功能描述:非熱縮管和套管 Corr. Loom Tubing Slit, .31" (7.9mm) X 1 RoHS:否 制造商:Panduit 產品:Cable Wraps 類型:Spiral 顏色:Black 材料:PP 內徑:0.03 in 長度:100 ft