- 您現在的位置：買賣IC網 > PDF目錄378828 > CH2056TBR (Electronic Theatre Controls, Inc.) HIGH SPEED Modem and FAX FAMILY PDF資料下載
參數資料
| 型號： | CH2056TBR |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | HIGH SPEED Modem and FAX FAMILY |
| 中文描述： | 高速調制解調器和傳真家庭 |
| 文件頁數： | 6/19頁 |
| 文件大?。?/td> | 365K |
| 代理商： | CH2056TBR |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁
Cermetek Microelectronics, Inc.
AT [Commands]<CR>.
Where:
AT
represents attention sequence.
A
and
T
may be either upper or lower case but must be
the same case. [
Command
] represents
command strings.
Where:
<CR>
represents carriage return (ASCII 13 or
HEX 0D)
<LF>
represents line feed (ASCII 10 or HEX
0A)
The HS Modem will respond with one of the following
status messages depending on whether it is optioned
for abbreviated (terse) or English (verbose) status
messages.
Result:
0 <CR>
(Terse)
or
Result:
<CR><LF>
OK
<CR><LF>
(Verbose)
After accepting the
AT<CR>
command the HS modem
is in idle mode and is ready to accept additional
commands.
An alternate attention sequence
A/
may be issued
which behaves much like the
AT
sequence except that
it causes the last entered command specified with an
AT
prefix to be executed. When given, it must be in
upper case ASCII. No carriage return is needed for
this command.
When entering commands to the modem, the
backspace character-control-H (ASCII 8 or HEX 08)
can be used to edit mistakes.
AT
and
A/
may not be
edited however. Multiple commands may be placed
on a command line. A command line may be as long
as 40 characters, excluding the letters
AT
. By way of
example, the command below instructs the HS Modem
to configure itself to not echo characters when in
command mode (
E0
) and then puts itself in answer
mode (
A
).
Enter:
ATE0A<CR>
Result:
OK<CR><LF>
AT Command Set.
The available command set is
divided into four types of commands: dial modifiers,
basic commands, ampersand and percent commands.
Refer to the complete list in Tables 6A and 6B.
INITIALIZING THE MODEM
Before commands may be sent to the HS Modem, the
modem must be initialized. This is a two step process:
Step 1. Modem Reset. This is accomplished by
applying a hardware-reset pulse to pin RST or
by switching the power off then back on.
High Speed Modem and FAX Family
2003 Cermetek Microelectronics, Inc.
Page 6
Document No. 607-0003 Revision K3 (09/03)
Step 2. Initial Modem Training. The modem must be
trained to the host DTE speed and parity (odd,
even, mark, space or none). These activities
are briefly described below.
HS Modem Reset.
Upon applying power to the HS
Modem, the HS Modem automatically generates an
internal reset pulse. The user can also reset the
modem externally by applying a high-going reset pulse
to the RST pin for at least 10 msec after the +5V
power supply has stabilized. Delay sending
commands to the HS Mode for 2 seconds after reset
has been initiated to allow the HS Modem time to
properly reconfigure.
On power up, or when reset is initiated either by the
ATZ<CR>
command or by the RST pin, the modem
will reconfigure to its default state with the line carrier
modulation speed set to:
1. 14.4kbps for the CH1794
2. 33.6kbps for the CH1799
3. 57.6kbps for the CH2056
If desired, any speed, error correction, or data
compression method available on the HS Modem can
be locked in, using the
ATNn
and/or
AT+MS
commands.
Training the Modem.
Each modem must be trained
to match the host DTE speed and parity so that it is
able to recognize serial asynchronous commands sent
to it by the DTE.
The DTE must retrain the modem each time a reset
pulse is applied on RST or after a RESET serial
command has been issued.
STATUS MESSAGES AND RESULTS CODES
A result code is issued by the HS Modem to the DTE
for all commands executed by the HS Modem except
dialing commands. Further, various activities on the
PSTN are also signaled to the DTE by the HS Modem.
All result codes have either a terse, short form version
(which is identified by a number followed by a
<CR>
)
or a verbose long form English-like message version
(which is preceded and terminated with a
<CR>
and
<LF>
).
The user may suppress certain subsets of the non-
extended result codes. This is accomplished by
selecting subsets of the result code set using the
ATXn
command, where n=0, 1, 2 or 3. Optionally, the
user may specify an extended set of results codes
(codes above 35) by setting Register S95. See the
detailed description of results codes in Table 5A, 5B
and 5C.
All
AT
commands, other than dialing commands, will
be responded to with either an OK (short form result
相關PDF資料 |
PDF描述 |
|---|---|
| CH1817 | Family of Low Profile DAA Modules |
| CH1817-DM | Family of Low Profile DAA Modules |
| CH1817-L | Family of Low Profile DAA Modules |
| CH1817-LM | Family of Low Profile DAA Modules |
| CH1817D | Family of Low Profile DAA Modules |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CH206 | 功能描述:重負荷電源連接器 HOODKIT206 RoHS:否 制造商:Hirose Connector 系列:PS2 產品類型:Connectors 位置/觸點數量: 端接類型:Crimp 觸點材料: 觸點電鍍:Gold 電壓額定值: 電流額定值:300 A 附件類型: |
| CH208 | 功能描述:重負荷電源連接器 HOODKIT208 RoHS:否 制造商:Hirose Connector 系列:PS2 產品類型:Connectors 位置/觸點數量: 端接類型:Crimp 觸點材料: 觸點電鍍:Gold 電壓額定值: 電流額定值:300 A 附件類型: |
| CH20H100R | 制造商:Eaton Corporation 功能描述:1Ph/CH Loadcenter 100A 42kAIC MCB 20 Cir. Cu Bus Nema 3R |
| CH20L100-A2 | 制造商:AIS 功能描述:20.1IN 1600X1200 1000:1 300NIT CHASSIS - Bulk |
| CH20L100-A3 | 制造商:AIS 功能描述:20.1 IN 16:9 1366X768 700:1 450NIT CHASS - Bulk |
發布緊急采購，3分鐘左右您將得到回復。