- 您現在的位置：買賣IC網 > PDF目錄9265 > CAT5171TBI-00GT3 (ON Semiconductor)IC POT DGTL 100K 256TAP SOT23-8 PDF資料下載
參數資料
| 型號： | CAT5171TBI-00GT3 |
| 廠商： | ON Semiconductor |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DGTL 100K 256TAP SOT23-8 |
| 標準包裝： | 3,000 |
| 接片： | 256 |
| 電阻（歐姆）： | 100k |
| 電路數： | 1 |
| 溫度系數： | 標準值 100 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SOT-23-8 |
| 供應商設備封裝： | SOT-23-8 |
| 包裝： | 帶卷 (TR) |
CAT5171
http://onsemi.com
7
BASIC OPERATION
The CAT5171 is a 256-position digitally controlled
potentiometer. When power is first applied, the wiper
assumes a mid-scale position. Once the power supply is
stable, the wiper may be repositioned via the I2C compatible
interface.
PROGRAMMING: VARIABLE RESISTOR
Rheostat Mode
The resistance between terminals A and B, RAB, has a
nominal value of 50 k
W or 100 kW and has 256 contact
points accessed by the wiper terminal, plus the B terminal
contact. Data in the 8-bit Wiper register is decoded to select
one of these 256 possible settings.
The wiper’s first connection is at the B terminal,
corresponding to control position 0x00. Ideally this would
present a 0
W between the Wiper and B, but just as with a
mechanical rheostat there is a small amount of contact
resistance to be considered, there is a wiper resistance
comprised of the RON of the FET switch connecting the
wiper output with its respective contact point. In CAT5171
this ‘contact’ resistance is typically 50
W. Thus a connection
setting of 0x00 yields a minimum resistance of 50
W
between terminals W and B.
For a 100 k
W device, the second connection, or the first tap
point, corresponds to 441
W (RWB = RAB/256 + RW = 390.6
+ 50
W) for data 0x01. The third connection is the next tap
point, is 831
W (2 x 390.6 + 50 W) for data 0x02, and so on.
Figure 11 shows a simplified equivalent circuit where the
last resistor string will not be accessed; therefore, there is
1 LSB less of the nominal resistance at full scale in addition
to the wiper resistance.
Figure 11. CAT5171 Equivalent Digital POT Circuit
RS
Wiper
Register
and
Decoder
A
W
B
RS
The equation for determining the digitally programmed
output resistance between W and B is
RWB + D
256
RAB ) RW
(eq. 1)
where D is the decimal equivalent of the binary code loaded
in the 8-bit Wiper register, RAB is the end-to-end resistance,
and RW is the wiper resistance contributed by the on
resistance of the internal switch.
In summary, if RAB = 100 kW and the A terminal is open
circuited, the following output resistance RWB will be set for
the indicated Wiper register codes:
Table 9. CODES AND CORRESPONDING RWB
RESISTANCE FOR RAB = 100 kW, VDD = 5 V
D (Dec.)
RWB (W)
Output State
255
99,559
Full Scale (RAB – 1 LSB + RW)
128
50,050
Midscale
1
441
1 LSB
0
50
Zero Scale
(Wiper Contact Resistance)
Be aware that in the zero-scale position, the wiper
resistance of 50
W is still present. Current flow between W
and B in this condition should be limited to a maximum
pulsed current of no more than 20 mA. Failure to heed this
restriction can cause degradation or possible destruction of
the internal switch contact.
Similar to the mechanical potentiometer, the resistance of
the digital POT between the wiper W and terminal A also
produces a digitally controlled complementary resistance
RWA. When these terminals are used, the B terminal can be
opened. Setting the resistance value for RWA starts at a
maximum value of resistance and decreases as the data
loaded in the latch increases in value. The general equation
for this operation is
RWA(D) +
256 * D
256
RAB ) RW
(eq. 2)
For RAB = 100 kW and the B terminal open circuited, the
following output resistance RWA will be set for the indicated
Wiper register codes.
Table 10. CODES AND CORRESPONDING RWA
RESISTANCE FOR RAB = 100 kW, VDD = 5 V
D (Dec.)
RWA (W)
Output State
255
441
Full Scale
128
50,050
Midscale
1
99,659
1 LSB
0
100,050
Zero Scale
Typical device to device resistance matching is lot
dependent and may vary by up to 20%.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B6B-MY-F4 | CONVERTER MOD DC/DC 95V 50W |
| VE-B6B-MY-F2 | CONVERTER MOD DC/DC 95V 50W |
| X93256WV14IZ-2.7 | IC XDCP DUAL 32TAP 12.5K 14TSSOP |
| VI-25R-MW | CONVERTER MOD DC/DC 7.5V 100W |
| VE-B6B-MY-F1 | CONVERTER MOD DC/DC 95V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT5171TBI-50GT3 | 功能描述:數字電位計 IC Linear Single 256 Taps Non Buffer RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| CAT5172TBI-00GT3 | 功能描述:數字電位計 IC Linear Single 256 Taps Non Buffer RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| CAT5172TBI-50GT3 | 功能描述:數字電位計 IC Linear Single 256 Taps Non Buffer RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| CAT5200 | 制造商:Datak Corporation 功能描述:Connector Accessories Jack Snap-in Icon Straight Yellow |
| CAT5200B | 制造商:Datak Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。