- 您現在的位置：買賣IC網 > PDF目錄9252 > CAT5112YI-00-GT3 (ON Semiconductor)IC POT DGTL 100L 32TAP 8TSSOP PDF資料下載
參數資料
| 型號： | CAT5112YI-00-GT3 |
| 廠商： | ON Semiconductor |
| 文件頁數： | 3/10頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DGTL 100L 32TAP 8TSSOP |
| 標準包裝： | 3,000 |
| 系列： | DPP |
| 接片： | 32 |
| 電阻（歐姆）： | 100k |
| 電路數： | 1 |
| 溫度系數： | 標準值 300 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 3 線串行（芯片選擇，遞增，增/減） |
| 電源電壓： | 2.5 V ~ 6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 8-TSSOP |
| 包裝： | 帶卷 (TR) |
CAT5112
http://onsemi.com
2
Figure 1. Functional Diagram
Figure 2. Electronic Potentiometer Implementation
Control
and
Memory
Power On Recall
GND
+
–
+
–
U/D
INC
CS
VCC
RWB
RH
RL
RWB
RL
RH
Pin Description
INC: Increment Control Input
The INC input (on the falling edge) moves the wiper in the
up or down direction determined by the condition of the U/D
input.
U/D: Up/Down Control Input
The U/D input controls the direction of the wiper movement.
When in a high state and CS is low, any hightolow
transition on INC will cause the wiper to move one
increment toward the RH terminal. When in a low state and
CS is low, any high-to-low transition on INC will cause the
wiper to move one increment towards the RL terminal.
RH: High End Potentiometer Terminal
RH is the high end terminal of the potentiometer. It is not
required that this terminal be connected to a potential greater
than the RL terminal. Voltage applied to the RH terminal
cannot exceed the supply voltage, VCC or go below ground,
GND.
RWB: Wiper Potentiometer Terminal (Buffered)
RWB is the buffered wiper terminal of the potentiometer. Its
position on the resistor array is controlled by the control
inputs, INC, U/D and CS.
RL: Low End Potentiometer Terminal
RL is the low end terminal of the potentiometer. It is not
required that this terminal be connected to a potential less
than the RH terminal. Voltage applied to the RL terminal
cannot exceed the supply voltage, VCC or go below ground,
GND. RL and RH are electrically interchangeable.
CS: Chip Select
The chip select input is used to activate the control input of
the CAT5112 and is active low. When in a high state, activity
on the INC and U/D inputs will not affect or change the
position of the wiper.
Device Operation
The CAT5112 operates like a digitally controlled
potentiometer with RH and RL equivalent to the high and low
terminals and RWB equivalent to the mechanical
potentiometer’s wiper. There are 32 available tap positions
including the resistor end points, RH and RL. There are 31
resistor elements connected in series between the RH and RL
terminals. The wiper terminal is connected to one of the 32
taps and controlled by three inputs, INC, U/D and CS. These
inputs control a five-bit up/down counter whose output is
decoded to select the wiper position. The selected wiper
position can be stored in nonvolatile memory using the INC
and CS inputs.
With CS set LOW the CAT5112 is selected and will
respond to the U/D and INC inputs. HIGH to LOW
transitions on INC will increment or decrement the wiper
(depending on the state of the U/D input and five-bit
counter). The wiper, when at either fixed terminal, acts like
its mechanical equivalent and does not move beyond the last
position. The value of the counter is stored in nonvolatile
memory whenever CS transitions HIGH while the INC input
is also HIGH. When the CAT5112 is powered-down, the last
stored wiper counter position is maintained in the
nonvolatile memory. When power is restored, the contents
of the memory are recalled and the counter is set to the value
stored.
With INC set low, the CAT5112 may be deselected and
powered down without storing the current wiper position in
nonvolatile memory. This allows the system to always
power up to a preset value stored in nonvolatile memory.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-26Y-MY-F1 | CONVERTER MOD DC/DC 3.3V 33W |
| VI-26Y-MX-F4 | CONVERTER MOD DC/DC 3.3V 49.5W |
| VI-26Y-MX-F3 | CONVERTER MOD DC/DC 3.3V 49.5W |
| VE-J54-MZ-S | CONVERTER MOD DC/DC 48V 25W |
| VI-26Y-MX-F1 | CONVERTER MOD DC/DC 3.3V 49.5W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT5112YI-00-T3 | 制造商:ON Semiconductor 功能描述:DPP, NV 32 TAPS, UP/DOWN W/BUF - Tape and Reel |
| CAT5112YI-00TE13 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:32-Tap Digitally Programmable Potentiometer |
| CAT5112YI10 | 制造商:ON Semiconductor 功能描述:DPP, NV 32 TAPS, UP/DOWN W/BUF - Rail/Tube |
| CAT5112YI-10 | 功能描述:數字電位計 IC Ind Temp 10K Up/Dwn RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| CAT5112YI-10-G | 制造商:ON Semiconductor 功能描述:DPP, NV 32 TAPS, UP/DOWN W/BUF - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。