參數資料
型號： C8051F305-GS
廠商： Silicon Laboratories Inc
文件頁數： 167/178頁
文件大?。?/td> 0K
描述： IC 8051 MCU 2K FLASH 14-SOIC
產品培訓模塊： Serial Communication Overview
標準包裝： 56
系列： C8051F30x
核心處理器： 8051
芯體尺寸： 8-位
速度： 25MHz
連通性： SMBus（2 線/I²C），UART/USART
外圍設備： POR，PWM，WDT
輸入/輸出數： 8
程序存儲器容量： 2KB（2K x 8）
程序存儲器類型： 閃存
RAM 容量： 256 x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 3.6 V
振蕩器型： 外部
工作溫度： -40°C ~ 85°C
封裝/外殼： 14-SOIC（0.154"，3.90mm 寬）
包裝： 管件
產品目錄頁面： 622 (CN2011-ZH PDF)
配用： 336-1444-ND - ADAPTER PROGRAM TOOLSTICK F300
其它名稱： 336-1540-5
Rev. 2.9
89
C8051F300/1/2/3/4/5
10. Flash Memory
On-chip, reprogrammable Flash memory is included for program code and non-volatile data storage. The
Flash memory can be programmed in-system, a single byte at a time, through the C2 interface or by soft-
ware using the MOVX instruction. Once cleared to logic 0, a Flash bit must be erased to set it back to logic
1. Flash bytes would typically be erased (set to 0xFF) before being reprogrammed. The write and erase
operations are automatically timed by hardware for proper execution; data polling to determine the end of
the write/erase operation is not required. Code execution is stalled during a Flash write/erase operation.
Refer to Table 10.1 for complete Flash memory electrical characteristics.
10.1. Programming The Flash Memory
The simplest means of programming the Flash memory is through the C2 interface using programming
tools provided by Silicon Labs or a third party vendor. This is the only means for programming a non-initial-
ized device. For details on the C2 commands to program Flash memory, see Section “17. C2 Interface”
To ensure the integrity of Flash contents, it is strongly recommended that the on-chip VDD Monitor
be enabled in any system that includes code that writes and/or erases Flash memory from soft-
ware.
10.1.1. Flash Lock and Key Functions
Flash writes and erases by user software are protected with a lock and key function; Flash reads by user
software are unrestricted. The Flash Lock and Key Register (FLKEY) must be written with the correct key
codes, in sequence, before Flash operations may be performed. The key codes are: 0xA5, 0xF1. The tim-
ing does not matter, but the codes must be written in order. If the key codes are written out of order, or the
wrong codes are written, Flash writes and erases will be disabled until the next system reset. Flash writes
and erases will also be disabled if a Flash write or erase is attempted before the key codes have been writ-
ten properly. The Flash lock resets after each write or erase; the key codes must be written again before a
following Flash operation can be performed. The FLKEY register is detailed in SFR Definition 10.2.
10.1.2. Flash Erase Procedure
The Flash memory can be programmed by software using the MOVX instruction with the address and data
byte to be programmed provided as normal operands. Before writing to Flash memory using MOVX, Flash
write operations must be enabled by: (1) setting the PSWE Program Store Write Enable bit (PSCTL.0) to
logic 1 (this directs the MOVX writes to target Flash memory); and (2) Writing the Flash key codes in
sequence to the Flash Lock register (FLKEY). The PSWE bit remains set until cleared by software.
A write to Flash memory can clear bits but cannot set them; only an erase operation can set bits in Flash.
A byte location to be programmed should be erased before a new value is written. The 8k byte Flash
memory is organized in 512-byte pages. The erase operation applies to an entire page (setting all bytes in
the page to 0xFF). To erase an entire 512-byte page, perform the following steps:
Step 1. Disable interrupts (recommended).
Step 2. Set the Program Store Erase Enable bit (PSEE in the PSCTL register).
Step 3. Set the Program Store Write Enable bit (PSWE in the PSCTL register).
Step 4. Write the first key code to FLKEY: 0xA5.
Step 5. Write the second key code to FLKEY: 0xF1.
Step 6. Using the MOVX instruction, write a data byte to any location within the 512-byte page to
be erased.
相關PDF資料
PDF描述
ISL84762IRZ IC SWITCH DUAL SPDT 10TDFN
ISL43L410IRZ IC SWITCH DPDT 10TDFN
DG211CYZ IC SWITCH QUAD SPST 16SOIC
ISL84523IVZ IC SWITCH QUAD SPST 16TSSOP
ISL84521IVZ IC SWITCH QUAD SPST 16TSSOP
相關代理商/技術參數
參數描述
C8051F305-GSR 功能描述:8位微控制器 -MCU 2KB 14Pin MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F305R 功能描述:8位微控制器 -MCU 303 2Kbyte RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F310 功能描述:8位微控制器 -MCU 16KB 10ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F310_1 制造商:SILABS 制造商全稱:SILABS 功能描述:8/16 kB ISP Flash MCU Family
C8051F310DK 功能描述:開發板和工具包 - 8051 MCU DEVELOPMENT KIT W/ US POWER SUPPLY RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*