參數資料
型號： BUF16820AIDAPR
英文描述： 14-Channel GAMMA VOLTAGE GENERATOR with Programmable VCOM Outputs and OTP Memory
中文描述： 14通道伽瑪電壓發生器具有可編程威科姆輸出和OTP存儲器
文件頁數： 23/30頁
文件大?。?/td> 681K
代理商： BUF16820AIDAPR
"#$%&'(
SBOS356A FEBRUARY 2006 REVISED OCTOBER 2006
www.ti.com
23
GENERAL POWERPAD DESIGN
CONSIDERATIONS
The BUF16820 is available in a thermally-enhanced
PowerPAD package. This package is constructed using a
downset leadframe upon which the die is mounted; see
Figure 22(a) and Figure 22(b). This arrangement results in
the lead frame being exposed as a thermal pad on the
underside of the package; see Figure 22(c). This thermal
pad has direct thermal contact with the die; thus, excellent
thermal performance is achieved by providing a good
thermal path away from the thermal pad.
The PowerPAD package allows for both assembly and
thermal management in one manufacturing operation.
During the surface-mount solder operation (when the
leads are being soldered), the thermal pad must be
soldered to a copper area underneath the package.
Through the use of thermal paths within this copper area,
heat can be conducted away from the package into either
a ground plane or other heat-dissipating device.
Soldering the PowerPAD to the printed circuit board
(PCB) is always required, even with applications that
have low power dissipation.
This provides the
necessary thermal and mechanical connection between
the lead frame die pad and the PCB.
The PowerPAD must be connected to the most negative
supply voltage on the device, GND
A
and GND
D
.
1.
Prepare the PCB with a top-side etch pattern. There
should be etching for the leads as well as for the
thermal pad.
Place recommended holes in the area of the thermal
pad. Ideal thermal land size and thermal via patterns
(3x6) for the HTSSOP-32 DAP package can be seen
in the technical brief,
PowerPAD Thermally-En-
hanced Package
(SLMA002), available for download
at www.ti.com. These holes should be 13 mils in diam-
eter. Keep them small, so that solder wicking through
the holes is not a problem during reflow.
2.
3.
Additional vias may be placed anywhere along the
thermal plane outside of the thermal pad area. This
helps dissipate the heat generated by the BUF16820
IC. These additional vias may be larger than the 13-mil
diameter vias directly under the thermal pad. They can
be larger because they are not in the thermal pad area
to be soldered; thus, wicking is not a problem.
Connect all holes to the internal plane that is at the
same voltage potential as the GND pins.
When connecting these holes to the internal plane, do
not use the typical web or spoke via connection
methodology. Web connections have a high thermal
resistance connection that is useful for slowing the
heat transfer during soldering operations. This makes
the soldering of vias that have plane connections
easier. In this application, however, low thermal
resistance is desired for the most efficient heat
transfer. Therefore, the holes under the BUF16820
PowerPAD package should make their connection to
the internal plane with a complete connection around
the entire circumference of the plated-through hole.
The top-side solder mask should leave the terminals
of the package and the thermal pad area with its ten
holes exposed. The bottom-side solder mask should
cover the holes of the thermal pad area. This masking
prevents solder from being pulled away from the
thermal pad area during the reflow process.
Apply solder paste to the exposed thermal pad area
and all of the IC terminals.
With these preparatory steps in place, the BUF16820
IC is simply placed in position and run through the
solder reflow operation as any standard surface-
mount component. This preparation results in a
properly installed part.
4.
5.
6.
7.
8.
相關PDF資料
PDF描述
BUF16820AIDAPRG4 14-Channel GAMMA VOLTAGE GENERATOR with Programmable VCOM Outputs and OTP Memory
BUF20800 18-Channel GAMMA VOLTAGE GENERATOR with Two Programmable VCOM Channels
BUF20800AIDCPR 18-Channel GAMMA VOLTAGE GENERATOR with Two Programmable VCOM Channels
BUF20820 18-Channel GAMMA VOLTAGE GENERATOR with Two Programmable VCOM Channels
BUF20820AIDCPR 18-Channel GAMMA VOLTAGE GENERATOR with Two Programmable VCOM Channels
相關代理商/技術參數
參數描述
BUF16820AIDAPRG4 功能描述:LCD Gamma緩沖器 14-Ch Vltg Generator w/2 Prog VCOM Out RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube
BUF16821 制造商:TI 制造商全稱:Texas Instruments 功能描述:Programmable Gamma-Voltage Generator and VCOM Calibrator with Integrated Two-Bank Memory
BUF16821_1 制造商:TI 制造商全稱:Texas Instruments 功能描述:Programmable Gamma-Voltage Generator and VCOM Calibrator with Integrated Two-Bank Memory
BUF16821A 制造商:TI 制造商全稱:Texas Instruments 功能描述:Programmable Gamma-Voltage Generator and VCOM Calibrator with Integrated Two-Bank Memory
BUF16821AIPWPR 功能描述:LCD Gamma緩沖器 Progammable Gamma Vltg Gen & Vcom Cal RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*