- 您現在的位置：買賣IC網 > PDF目錄369480 > BQ4847Y Fast Recovery Glass Passivated Rectifier Diodes PDF資料下載
參數資料
| 型號： | BQ4847Y |
| 英文描述： | Fast Recovery Glass Passivated Rectifier Diodes |
| 中文描述： | 時鐘模塊CPU監控 |
| 文件頁數： | 8/20頁 |
| 文件大?。?/td> | 1155K |
| 代理商： | BQ4847Y |
Interrupts
The bq4845 allows three individually selected interrupt
events to generate an interrupt request on the INT pin.
Thesethreeinterrupt events are:
I
The periodic interrupt, programmable to occur once
every 30.5
μ
s to 500ms
I
The alarm interrupt, programmable to occur once per
second to once per month
I
The power-fail interrupt, which can be enabled to be
asserted when the bq4845 detects a power failure
The periodic, alarm, and power-fail interrupts are en-
abled by an individual interrupt-enable bit in register C,
the interrupts register. When an event occurs, its event
flag bit in the flags register, register D, is set. If the cor-
responding event enable bit is also set, then an interrupt
request is generated. Reading the flags register clears
all flag bits and makes INT high impedance. To reset
the flag register, the bq4845 addresses must be held sta-
ble at register D for at least 50ns to avoid inadvertent
resets.
Periodic Interrupt
Bits RS3–RS0 in the interrupts register program the
rate for the periodic interrupt. The user can interpret
the interrupt in two ways: either by polling the flags
register for PF assertion or by setting PIE so that INT
goes active when the bq4845 sets the periodic flag.
Reading the flags register resets the PF bit and returns
INT to the high-impedance state. Table 4 shows the pe-
riodic rates.
Alarm Interrupt
Registers 1, 3, 5, and 7 program the real-time clock
alarm. During each update cycle, the bq4845 compares
the date, hours, minutes, and seconds in the clock regis-
ters with the corresponding alarm registers. If a match
between all the corresponding bytes is found, the alarm
flag AF in the flags register is set. If the alarm inter-
rupt is enabled with AIE, an interrupt request is gener-
ated on INT. The alarm condition is cleared by a read to
the flags register. ALM1 – ALM0 in the alarm registers,
mask each alarm compare byte. An alarm byte is
masked by setting ALM1 (D7) and ALM0 (D6) to 1.
Alarm byte masking can be used to select the frequency
of thealarm interrupt, according toTable5.
The alarm interrupt can be made active while the
bq4845 is in the battery-backup mode by setting ABE in
the interrupts register.
Normally, the INT pin goes
high-impedance during battery backup. With ABE set,
however, INT is driven low if an alarm condition occurs
and the AIE bit is set. Because the AIE bit is reset dur-
ing power-on reset, an alarm generated during power-on
reset updates only the flags register. The user can read
the flags register during boot-up to determine if an
alarm was generated during power-on reset.
Power-Fail Interrupt
When V
CC
falls to the power-fail-detect point, the
power-fail flag PWRF is set. If the power-fail interrupt
enable bit (PWRIE) is also set, then INT is asserted low.
The power-fail interrupt occurs t
WPT
before the bq4845
generates a reset and deselects.
cleared on power-up.
The PWRIE bit is
Battery-Low Warning
The bq4845 checks the battery on power-up. When the
battery voltage is approximately 2.1V, the battery-valid
flag BVF in the flags register is set to a 0 indicating that
clock and RAM data may beinvalid.
8
WD2
0
WD1
0
WD0
0
Normal Watchdog
Time-out Period (t
2
, t
3
)
1.5s
Reset Time-out
Period (t
1
)
0.25s
0
0
1
23.4375ms
3.9063ms
0
1
0
46.875ms
7.8125ms
0
1
1
93.75ms
15.625ms
1
0
0
187.5ms
31.25ms
1
0
1
375ms
62.5ms
1
1
0
750ms
125ms
1
1
1
3s
0.5s
Table 3. Watchdog Time-out Rates
Aug. 1995
bq4845/bq4845Y
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料 |
PDF描述 |
|---|---|
| BQ48S1.5-30A | Fast Recovery Glass Passivated Rectifier Diodes |
| BQ48S2-40R | DC to DC Converter |
| BQ48S2-40T | DC to DC Converter |
| BQ48S3.3-66A | DC to DC Converter |
| BQ48S3.3-66R | DC to DC Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ4847YMT | 功能描述:實時時鐘 RTC with NVSRAM RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| BQ4847Y-MT | 制造商:TI 制造商全稱:Texas Instruments 功能描述:RTC Module With CPU Supervisor |
| BQ4850Y | 制造商:TI 制造商全稱:Texas Instruments 功能描述:RTC Module With 512Kx8 NVSRAM |
| BQ4850Y_13 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:RTC Module With 512Kx8 NVSRAM |
| BQ4850YMA-85 | 功能描述:實時時鐘 RTC Module 512Kx8 NVSRAM RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。