- 您現在的位置：買賣IC網 > PDF目錄373024 > BQ24205DGNR Fast Recovery Bridge Rectifiers PDF資料下載
參數資料
| 型號： | BQ24205DGNR |
| 英文描述： | Fast Recovery Bridge Rectifiers |
| 中文描述： | 模擬IC |
| 文件頁數： | 11/14頁 |
| 文件大?。?/td> | 201K |
| 代理商： | BQ24205DGNR |
SLUS501A
–
OCTOBER 2001
11
www.ti.com
APPLICATION INFORMATION
battery charge current
Following a successful pre-conditioning, the bq2420x relies on an external current-limited supply to limit the
charge current to the cell. The bq2420x continues this phase until the battery reaches the voltage regulation
phase.
During this phase (and all other phases of operation) in order to protect the integrated powerFET, the internal
short circuit and thermal protection circuits are active.
battery voltage regulation
The voltage regulation feedback is through the BAT pin. This input is tied directly to the positive side of the
battery pack. The bq2420x monitors the battery-pack voltage between the BAT and VSS pins. The bq2420x
is offered in two fixed-voltage versions: 4.1 V and 4.2 V.
As a safety backup, the bq2420x also monitors the charge time in the voltage regulation mode. If taper current
is not detected within this time period, t
(CHG)
, the bq2420x turns off the charger and enunciates FAULT on the
STAT pin. Fault condition is cleared by POR or battery replacement. Note that the safety timer is reset if the
bq2420x is forced out of the voltage regulation mode.
charge termination and recharge
The bq2420x monitors the charging current during the voltage regulation phase. Once the taper threshold,
I
(TAPER)
, is detected the bq2420x initiates the taper timer, t
(TAPER)
. Charge is terminated after the timer expires.
The bq2420x resets the taper timer in the event that the charge current returns above the taper threshold,
I
(TAPER).
In addition to the taper current detection, the bq2420x terminates charge in the event that the charge current
falls below the I
(TERM)
threshold. This feature allows for quick recognition of a battery removal condition.
After a charge termination, the bq2420x restarts the charge once the voltage on the BAT pin falls below the
V
(RCH)
threshold. This feature keeps the battery at full capacity at all times.
sleep mode
The bq2420x enters the low-power sleep mode if the Vcc is removed from the circuit (i.e. the Vcc and IN pins
are floating). For applications where these pins are not floating, placing a low-power 10
(1/16 W) between
the IN and VCC pins ensures the V
(SLP)
conditions are met (see Figure 9).This feature prevents draining the
battery during the absence of V
CC
.
P
相關PDF資料 |
PDF描述 |
|---|---|
| BQ24901 | Fast Recovery Bridge Rectifiers |
| BQ2902PN-N | Battery Management |
| BQ2902SN-N | Battery Management |
| BQ3EG | Avalanche Glass Passivated Bridge Rectifiers |
| BQ3GJ | Avalanche Glass Passivated Bridge Rectifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ24205DGNRG4 | 功能描述:電池管理 Single-Chip Li-Ion Charger RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ24210 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:800mA, Single-Input, Single Cell Li-Ion Battery Solar Charger |
| BQ24210DQCR | 功能描述:電池管理 800mA,Sgl-Inp,Li-Ion Solar Batt Charger RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ24210DQCT | 功能描述:電池管理 800mA,Sgl-Inp,Li-Ion Solar Batt Charger RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ24210EVM678 | 制造商:Texas Instruments 功能描述:Evaluation Module For Single-Input, Single-Cell Li-Ion Battery Charger |
發布緊急采購，3分鐘左右您將得到回復。