- 您現在的位置：買賣IC網 > PDF目錄298840 > ATH15T05-9S 1-OUTPUT 66 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | ATH15T05-9S |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 66 W DC-DC REG PWR SUPPLY MODULE |
| 文件頁數： | 4/14頁 |
| 文件大?。?/td> | 408K |
| 代理商： | ATH15T05-9S |
Application Notes
ATH Series of Wide-Output Adjust Power
Modules (3.3/5-V Input)
North America (USA): 1-888-41-ASTEC
Europe (UK): 44(1384)842-211
Asia (HK): 852-2437-9662
Pre-Bias Startup Capability
Only selected products in the ATH family incorporate this
capability. Consult Table 3-1 to identify which products
are compliant.
A pre-bias startup condition occurs as a result of an external
voltage being present at the output of a power module prior
to its output becoming active. This often occurs in com-
plex digital systems when current from another power
source is backfed through a dual-supply logic component,
such as an FPGA or ASIC. Another path might be via
clamp diodes as part of a dual-supply power-up sequencing
arrangement. A prebias can cause problems with power
modules that incorporate synchronous rectifiers. This is
because under most operating conditions, these types of
modules can sink as well as source output current.
The ATH family of power modules incorporate synchro-
nous rectifiers, but will not sink current during startup 1,
or whenever the Inhibit pin is held low. However, to ensure
satisfactory operation of this function, certain conditions
must be maintained. 2 Figure 3-7 shows an application
demonstrating the pre-bias startup capability. The start-
up waveforms are shown in Figure 3-9. Note that the
output current from the ATH15T033-9xx (Io) shows neg-
ligible current until its output voltage rises above that
backfed through diodes D1 and D2.
Note: The pre-bias start-up feature is not compatible with
Auto-Track. When the module is under Auto-Track control, it
is fully active and will sink current if the output voltage is
below that of a back-feeding source. Therefore to ensure a pre-
bias hold-off, one of two approaches must be followed when
input power is applied to the module. The Auto-Track function
must either be disabled 3, or the module’s output held off using
the Inhibit pin. The latter allows Auto-Track’s internal (RC)
voltage ramp to rise above the set-point voltage.
Notes
1. Startup is the relatively short period (approx. 10 ms)
prior to the output voltage rising. The startup period
immediately follows either the application of a valid
input source voltage, or the release of a ground signal
at the Inhibit pin.
2. To ensure that the regulator does not sink current when
power is first applied (even with a ground signal applied
to the Inhibit control pin), the input voltage must always
be greater than the output voltage throughout the
power-up and power-down sequence.
3. The Auto-Track function can be disabled at power up
by immediately applying a voltage to the module’s Track
pin that is greater than its set-point voltage. This can
be easily accomplished by connecting the Track pin to
Vin through a 1-k resistor.
V
o = 2.5 V
V
IN = 3.3 V
R
2
2k21
R
1
1k0
ASIC
VCORE
VCCIO
I
o
PTH03010W
1
10
4
5
6
2
3
98
Track
V
IN
V
O
GND
Inhibit
7
Vadj
Sense
+
C
IN
330 F
+
D
1, D2
MBR3100
C
OUT
330 F
+
Figure 3.8; Application Circuit Demonstrating Pre-Bias Startup
Vin (1 V/Div)
Vo (1 V/Div)
Io (5 A/Div)
HORIZ SCALE: 5 ms/Div
Figure 3.9; Pre-Bias Startup Waveforms
ATH15T033-9S
相關PDF資料 |
PDF描述 |
|---|---|
| ATO2815T | 3-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| ATT17128AM20I | 128K X 1 CONFIGURATION MEMORY, PQCC20 |
| ATT1736AG8I-DT | 36288 X 1 OTPROM, PDSO8 |
| AU1550500MBC | 500 MHz, MICROPROCESSOR, PBGA483 |
| AU1PDHM3/84A | 1 A, 200 V, SILICON, SIGNAL DIODE, DO-220AA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATH15T05-9SJ | 功能描述:DC/DC轉換器 DC-DC 1OUT 0.8V-3.6V 15A 66W 10-Pin SMT RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| ATH15T05-9SJL | 功能描述:DC/DC轉換器 DC-DC 1OUT 0.8V-3.6V 15A 66W 10-Pin SMT RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| ATH15T05-9SL | 功能描述:DC/DC轉換器 DC-DC 1OUT 0.8V-3.6V 15A 66W 10-Pin SMT RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| ATH18 | 制造商:ASTEC 制造商全稱:Astec America, Inc 功能描述:6-A, 3.3-V Input Non-Isolated Wide-Output Adjust Power Module |
| ATH18K12 | 制造商:ASTEC 制造商全稱:Astec America, Inc 功能描述:18-A, 12-V Input Non-Isolated Wide-Output Adjust Power Module |
發布緊急采購，3分鐘左右您將得到回復。