- 您現在的位置：買賣IC網 > PDF目錄381451 > AT43USB355E-AC (ATMEL CORP) Full-speed USB Microcontroller with Embedded Hub, ADC and PWM PDF資料下載
參數資料
| 型號： | AT43USB355E-AC |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Full-speed USB Microcontroller with Embedded Hub, ADC and PWM |
| 中文描述： | 8-BIT, MROM, 12 MHz, RISC MICROCONTROLLER, PQFP64 |
| 封裝： | 1.40 MM, PLASTIC, MS-026ACB, LQFP-64 |
| 文件頁數： | 86/115頁 |
| 文件大小： | 610K |
| 代理商： | AT43USB355E-AC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁當前第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁
86
AT43USB355
2603G–USB–04/06
Hub End-point 0 Service Routine Register – HCSR0
Function End-point 0 Service Routine Register – FCSR0
Bit 7..4 – Reserved
These bits are reserved in the AT43USB355 and will read as zero.
Bit 3 – STALL SENT
The USB hardware sets this bit after a STALL has been sent to the host. The firmware uses
this bit when responding to a Get Status[End-point] request. It is a read only bit and that is
cleared indirectly by writing a one to the STALL_SENT_ACK bit of the Control and Acknowl-
edge Register.
Bit 2 – RX SETUP: Setup Packet Received
This bit is used by control end-points only to signal to the microcontroller that the USB hard-
ware has received a valid SETUP packet and that the data portion of the packet is stored in
the FIFO. The hardware will clear all other bits in this register while setting RX SETUP. If inter-
rupt is enabled, the microcontroller will be interrupted when RX SETUP is set. After the
completion of reading the data from the FIFO, firmware should clear this bit by writing a one to
the RX_SETUP_ACK bit of the Control and Acknowledge Register.
Bit 1 – RX OUT PACKET
The USB hardware sets this bit after it has stored the data of an OUT transaction in the FIFO.
While this bit is set, the hardware will NAK all OUT tokens. The USB hardware will not over-
write the data in the FIFO except for an early set-up. RX OUT Packet is used for the following
operations:
1.
Control write transactions by a control end-point.
2.
OUT transaction with DATA1 PID to complete the status phase of a control end-point.
Setting this bit causes an interrupt to the microcontroller if the interrupt is enabled. FW clears
this bit after the FIFO contents have been read by writing a one to the
RX_OUT_PACKET_ACK bit of the Control and Acknowledge Register.
Bit 0 – TX COMPL: Transmit Completed
This bit is used by a control end-point hardware to signal to the microcontroller that it has suc-
cessfully completed certain transactions. TX Complete is set at the completion of a:
1.
Control read data stage.
2.
Status stage without data stage.
3.
Status stage after a control write transaction.
This bit is read only and is cleared indirectly by writing a one to the TX_COMPLETE_ACK bit
of the Control and Acknowledge Register.
Bit
7
6
5
4
3
2
1
0
Function EP0 $1FDF
–
–
–
–
STALL SENT
RX SETUP
RX OUT PACKET
TX COMPLETE
HCSR0
Function EP0 $1FDD
–
–
–
–
STALL SENT
RX SETUP
RX OUT PACKET
TX COMPLETE
FCSR0
Read/Write
R
R
R
R
R
R
R
R
Initial Value
0
0
0
0
0
0
0
0
相關PDF資料 |
PDF描述 |
|---|---|
| AT43USB355E-AU | Full-speed USB Microcontroller with Embedded Hub, ADC and PWM |
| AT43USB355M-AC | Full-speed USB Microcontroller with Embedded Hub, ADC and PWM |
| AT43USB355M-AU | Full-speed USB Microcontroller with Embedded Hub, ADC and PWM |
| AT43USB380 | On-The-Go Upgrade of the AT43USB370 USB 2.0 Full-Speed Host/Function Processor |
| AT45BR3214B | 32-MEGABIT DATAFLASH + 4-MEGABIT SRAM STACK MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT43USB355E-AU | 功能描述:8位微控制器 -MCU USB GAME CONTROL w/ EMBED HUB RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| AT43USB355M-AC | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Full-speed USB Microcontroller with Embedded Hub, ADC and PWM |
| AT43USB355M-AU | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Full-speed USB Microcontroller with Embedded Hub, ADC and PWM |
| AT43USB370 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:USB 2.0 Full-Speed Host/Function Processor |
| AT43USB370E-AC | 功能描述:USB 接口集成電路 USB HOST DEVICE CONTROL - COM TEMP RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。