- 您現在的位置：買賣IC網 > PDF目錄381451 > AT43USB355E-AC (ATMEL CORP) Full-speed USB Microcontroller with Embedded Hub, ADC and PWM PDF資料下載
參數資料
| 型號： | AT43USB355E-AC |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Full-speed USB Microcontroller with Embedded Hub, ADC and PWM |
| 中文描述： | 8-BIT, MROM, 12 MHz, RISC MICROCONTROLLER, PQFP64 |
| 封裝： | 1.40 MM, PLASTIC, MS-026ACB, LQFP-64 |
| 文件頁數： | 19/115頁 |
| 文件大?。?/td> | 610K |
| 代理商： | AT43USB355E-AC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁
19
AT43USB355
2603G–USB–04/06
Functional Description
On-chip Power
Supply
The AT43USB355 contains four on-chip power supplies that generate 3.3V with a capacity of
30 mA each from the 5V power input. The on-chip power supplies are intended to supply the
AT43USB355 internal circuit and the 1.5K pull-up resistor only and should not be used for
other purposes. External 2.2 μF filter capacitors are required at the power supply outputs,
CEXT1, 2, 3, and a 0.33 μF capacitor for CEXTA. The internal power supplies can be disabled
as described in the next paragraph.
The user should be careful when the GPIO pins are required to supply high-load currents. If
the application requires that the GPIO supply currents beyond the capability of the on-chip
power supply, the AT43USB355 should be supplied by an external 3.3V power supply. In this
case, the 5V V
CC
power supply pin should be left unconnected and the 3.3V power supplied to
the chip through the CEXT1, 2, 3 and CEXTA pins.
I/O Pin
Characteristics
The I/O pins of the AT43USB355 should not be directly connected to voltages less than V
SS
or
more than the voltage at the CEXT pins. If it is necessary to violate this rule, insert a series
resistor between the I/O pin and the source of the external signal source that limits the current
into the I/O pin to less than 2 mA. Under no circumstance should the external voltage exceed
5.5V. To do so will put the chip under excessive stress.
Oscillator and PLL
All clock signals required to operate the AT43USB355 are derived from an on-chip oscillator.
To reduce EMI and power dissipation, the oscillator is designed to operate with a 6 MHz crys-
tal. An on-chip PLL generates the high frequency for the clock/data separator of the Serial
Interface Engine. In the suspended state, the oscillator circuitry is turned off.
The oscillator of the AT43USB355 is a special, low-drive type, designed to work with most
crystals without any external components. The crystal must be of the parallel resonance type
requiring a load capacitance of about 10 pF. If the crystal requires a higher value capacitance,
external capacitors can be added to the two terminals of the crystal and ground to meet the
required value. To assure quick start-up, a crystal with a high Q, or low ESR, should be used.
To meet the USB hub frequency accuracy and stability requirements for hubs, the crystal
should have an accuracy and stability of better than 100 PPM. The use of a ceramic resonator
in place of the crystal is not recommended because a resonator would not have the necessary
frequency accuracy and stability.
The clock can also be externally sourced. In this case, connect the clock source to the XTAL1
pin, while leaving XTAL2 pin floating. The switching level at the OSC1 pin can be as low as
0.47V and a CMOS device is required to drive this pin to maintain good noise margins at the
low switching level.
For proper operation of the PLL, an external RC filter consisting of a series RC network of
100
and 0.1 μF in parallel with a 0.01 μF capacitor must be connected from the LFT pin to
V
SS
. Use only high-quality ceramic capacitors.
相關PDF資料 |
PDF描述 |
|---|---|
| AT43USB355E-AU | Full-speed USB Microcontroller with Embedded Hub, ADC and PWM |
| AT43USB355M-AC | Full-speed USB Microcontroller with Embedded Hub, ADC and PWM |
| AT43USB355M-AU | Full-speed USB Microcontroller with Embedded Hub, ADC and PWM |
| AT43USB380 | On-The-Go Upgrade of the AT43USB370 USB 2.0 Full-Speed Host/Function Processor |
| AT45BR3214B | 32-MEGABIT DATAFLASH + 4-MEGABIT SRAM STACK MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT43USB355E-AU | 功能描述:8位微控制器 -MCU USB GAME CONTROL w/ EMBED HUB RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| AT43USB355M-AC | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Full-speed USB Microcontroller with Embedded Hub, ADC and PWM |
| AT43USB355M-AU | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Full-speed USB Microcontroller with Embedded Hub, ADC and PWM |
| AT43USB370 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:USB 2.0 Full-Speed Host/Function Processor |
| AT43USB370E-AC | 功能描述:USB 接口集成電路 USB HOST DEVICE CONTROL - COM TEMP RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。