- 您現在的位置：買賣IC網 > PDF目錄381451 > AT43USB325E-AC (ATMEL CORP) Multimedia USB Keyboard Controller with Embedded Hub PDF資料下載
參數資料
| 型號： | AT43USB325E-AC |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Multimedia USB Keyboard Controller with Embedded Hub |
| 中文描述： | 8-BIT, 12 MHz, RISC MICROCONTROLLER, PQFP64 |
| 封裝： | 1.40 MM HEIGHT, PLASTIC, MS-026-ACB, LQFP-64 |
| 文件頁數： | 20/109頁 |
| 文件大?。?/td> | 643K |
| 代理商： | AT43USB325E-AC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁
20
3355C–USB–4/05
AT43USB325
4.
Functional Description
4.1
On-chip Power Supply
The AT43USB325 contains two on-chip power supplies that generate 3.3V with a capacity of 30
mA each from the 5V power input. The on-chip power supplies are intended to supply the
AT43USB325 internal circuit and the 1.5K pull-up resistor only and should not be used for other
purposes. External 2.2 μF filter capacitors are required at the power supply outputs, CEXT1 and
CEXT2. The internal power supplies can be disabled as described in the next paragraph.
The user should be careful when the GPIO pins are required to supply high-load currents. If the
application requires that the GPIO supply currents beyond the capability of the on-chip power
supply, the AT43USB325 should be supplied by an external 3.3V power supply. In this case, the
5V V
CC
power supply pin should be left unconnected and the 3.3V power supplied to the chip
through the CEXT1 and CEXT2 pins.
4.2
I/O Pin Characteristics
The I/O pins of the AT43USB325 should not be directly connected to voltages less than V
SS
or
more than the voltage at the CEXT pins. If it is necessary to violate this rule, insert a series resis-
tor between the I/O pin and the source of the external signal source that limits the current into
the I/O pin to less than 2 mA. Under no circumstance should the external voltage exceed 5.5V.
To do so will put the chip under excessive stress.
4.3
Oscillator and PLL
All clock signals required to operate the AT43USB325 are derived from an on-chip oscillator. To
reduce EMI and power dissipation, the oscillator is designed to operate with a 6 MHz crystal. An
on-chip PLL generates the high frequency for the clock/data separator of the Serial Interface
Engine. In the suspended state, the oscillator circuitry is turned off.
The oscillator of the AT43USB325 is a special, low-drive type, designed to work with most crys-
tals without any external components. The crystal must be of the parallel resonance type
requiring a load capacitance of about 10 pF. If the crystal requires a higher value capacitance,
external capacitors can be added to the two terminals of the crystal and ground to meet the
required value. To assure quick start-up, a crystal with a high Q, or low ESR, should be used. To
meet the USB hub frequency accuracy and stability requirements for hubs, the crystal should
have an accuracy and stability of better than 100 PPM. The use of a ceramic resonator in place
of the crystal is not recommended because a resonator would not have the necessary frequency
accuracy and stability.
The clock can also be externally sourced. In this case, connect the clock source to the XTAL1
pin, while leaving XTAL2 pin floating. The switching level at the OSC1 pin can be as low as
0.47V and a CMOS device is required to drive this pin to maintain good noise margins at the low
switching level.
For proper operation of the PLL, an external RC filter consisting of a series RC network of 100
and 0.1 μF in parallel with a 0.01 μF capacitor must be connected from the LFT pin to V
SS
. Use
only high-quality ceramic capacitors.
相關PDF資料 |
PDF描述 |
|---|---|
| AT43USB325E-AU | Multimedia USB Keyboard Controller with Embedded Hub |
| AT43USB326-AC | Multimedia USB Keyboard Controller with Embedded Hub |
| AT43USB326-AU | Multimedia USB Keyboard Controller with Embedded Hub |
| AT43USB351M-AC | Full-speed/Low-speed USB Microcontroller with ADC and PWM |
| AT43USB353M-AC | Low Cost Full-speed USB Microcontroller with Embedded Hub, ADC and PWM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT43USB325E-AU | 功能描述:USB 接口集成電路 USB KEYBOARD CONTROL w/HUB - IND TEMP RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| AT43USB326 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Missed Watchdog Timer Reset |
| AT43USB326_06 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Multimedia USB Keyboard Controller with Embedded Hub |
| AT43USB326-AC | 功能描述:USB 接口集成電路 USB KEYBOARD F/LOGI- TECH - COM TEMP RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| AT43USB326-AU | 功能描述:USB 接口集成電路 USB KEYBOARD FOR LOGITECH - IND TEMP RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。