- 您現在的位置：買賣IC網 > PDF目錄381451 > AT43312 (Atmel Corp.) Self- and Bus- Powered USB Hub Controller PDF資料下載
參數資料
| 型號： | AT43312 |
| 廠商： | Atmel Corp. |
| 英文描述： | Self- and Bus- Powered USB Hub Controller |
| 中文描述： | 自和總線供電的USB集線器控制器 |
| 文件頁數： | 3/21頁 |
| 文件大?。?/td> | 157K |
| 代理商： | AT43312 |
AT43312
3
Note:
Signals with a # are active low.
Pin Description
Pin Description
Pin Type
Description
OSC1
I
Oscillator Input. Input to the inverting 6 MHz oscillator amplifier.
OSC2
O
Oscillator Output. Output of the inverting oscillator amplifier.
LFT
I
PLL Filter. For proper operation of the PLL, this pin should be connected through a 2.2 nF capacitor in
parallel with a 100
resistor in series with a 10 nF capacitor to ground (GND)
BUS/SELF
I
Hub Power Mode. Input signal that sets the bus or self-powered mode operation. A high on this pin
enables the bus-powered mode, a low the self-powered mode.
VREF
I
Reference Voltage. This is an input pin that should be connected to an external voltage source. V
REF
is used internally as the reference voltage by the overload protection circuit to decide whether there is
a problem with a port’s power.
DP0
B
Upstream Plus USB I/O. This pin should be connected to V
CC
through an external 1.5 K
pullup
resistor. DP0 and DM0 form the differential signal pin pairs connected to the Host Controller or an
upstream Hub.
DM0
B
Upstream Minus USB I/O
DP[1:4]
B
Port Plus USB I/O. This pin should be connected to V
SS
through an external 15 K
resistor. DP[1:4]
and DM[1:4] are the differential signal pin pairs to connect downstream USB devices.
DM[1:4]
B
Port Minus USB I/O. This pin should be connected to V
SS
through an external 15 K
resistor.
OVC[1:4]
I
Overcurrent. This is the input signal used to indicate to the AT43312 that an overcurrent is detected at
the port. If OVC is asserted, AT43312 will assert the PWRx pin and report the status to the USB Host.
PWR[1:4]
OD
Power Switch. This is an output signal used to enable or disable the external voltage regulator
supplying power to a port. PWRx is de-asserted when a power supply problem is detected at OVCx.
STAT[1:4]
O
Connect Status. This is an output pin indicating that a port is properly connected. STATx is asserted
when the port is enabled.
V
CC3
V
3.3V Power Supply
V
CC5
V
5V Power Supply
V
CCA
V
5V Analog Power Supply
GND
V
Ground
相關PDF資料 |
PDF描述 |
|---|---|
| AT43320 | Full-speed USB Hub/Function Microcontroller |
| AT43DK301 | Low-Cost USB Hub Development Kit |
| AT43DK312A | USB Hub Development Kit |
| AT43USB320A-AC | Full-speed USB Microcontroller with an Embedded Hub |
| AT43USB321 | Full-speed USB Hub/Function Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT43312(32DIP) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:BUS CONTROLLER |
| AT43312(32SOIC) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:BUS CONTROLLER |
| AT43312A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:AT43312A [Updated 7/03. 27 Pages] |
| AT43312A_06 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Self- and Bus-Bus-powered USB Hub Controller |
| AT43312A-6AC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:BUS CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。