- 您現在的位置：買賣IC網 > PDF目錄381451 > AT43312 (Atmel Corp.) Self- and Bus- Powered USB Hub Controller PDF資料下載
參數資料
| 型號： | AT43312 |
| 廠商： | Atmel Corp. |
| 英文描述： | Self- and Bus- Powered USB Hub Controller |
| 中文描述： | 自和總線供電的USB集線器控制器 |
| 文件頁數： | 13/21頁 |
| 文件大?。?/td> | 157K |
| 代理商： | AT43312 |
AT43312
13
Hub-specific Requests
Hub-specific requests or commands are sent from the Host
to the AT43312 using the Default Pipe (associated with
Endpoint0). These requests are made using control trans-
fers. The request and request parameters are sent in a
setup packet consisting of eight bytes. Please refer to the
USB specifications for details.
Clear_Hub_Feature
This request is used by the host to acknowledge local
power and hub overcurrent changes. Upon receipt of this
request with a wValue = 0, the AT43312 will clear the Local
Power Status Change bit. The AT43312 has a per port
overcurrent protection and does not report over-current on
a global basis. If this request has a wValue = 1, the
AT43312 will respond with a STALL.
Clear_Port_Feature
This request changes the status of a port according to
which port feature the request addressess. Not all the pos-
sible port features are supported, because some have no
meaning. Port features supported by the
Clear_Port_Feature request are: PORT_ENABLE,
PORT_SUSPEND, PORT_POWER, and all those affecting
the port status change bits. A request with an unsupported
feature, or if Port0 or a port higher than Port4 is addressed,
will cause the hub to respond with a STALL.
Get_Bus_State
The AT43311 samples the bus states of Ports 1, 2, 3, and
4, at each EOF2 and will store the value in a register known
as the Port_Bus_State registers. The value of the D- signal
(pin DMx) will be in bit 0 and the value of the D+ signal
(DPx) will be in bit 1 of each port’s Port_Bus_State register.
All other bits will be 0. The AT43311 responds with a
STALL if Port0 or a port higher than Port4 is addressed in
this request.
Get_Hub_Descriptor
Returns the Hub Descriptor. The last word of the
Get_Hub_Descriptor request specifies the number of bytes
AT43312 is to return. If the requested number of bytes is
less than the 9 bytes length of the HubDescriptor, the
AT43312 will return only the requested number of bytes
from the top of the descriptor. If the requested number of
bytes is more than 9, then the returned data will be padded
with trailing bytes of zeroes.
Get_Hub_Status
Returns the current Hub status that has changed since the
previous acknowledgment in the form of two words of data.
This is described in the following two tables. Word0 is the
Hub Status Field, wHubStatus, and Word1 is the Hub
Change Field, wHubChange.
相關PDF資料 |
PDF描述 |
|---|---|
| AT43320 | Full-speed USB Hub/Function Microcontroller |
| AT43DK301 | Low-Cost USB Hub Development Kit |
| AT43DK312A | USB Hub Development Kit |
| AT43USB320A-AC | Full-speed USB Microcontroller with an Embedded Hub |
| AT43USB321 | Full-speed USB Hub/Function Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT43312(32DIP) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:BUS CONTROLLER |
| AT43312(32SOIC) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:BUS CONTROLLER |
| AT43312A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:AT43312A [Updated 7/03. 27 Pages] |
| AT43312A_06 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Self- and Bus-Bus-powered USB Hub Controller |
| AT43312A-6AC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:BUS CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。