- 您現在的位置：買賣IC網 > PDF目錄67389 > AT42QT1111-AU (ATMEL CORP) PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | AT42QT1111-AU |
| 廠商： | ATMEL CORP |
| 元件分類： | 速度傳感器和接近開關 |
| 英文描述： | PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT |
| 封裝： | 7 X 7 MM, 1 MM HEIGHT, 0.80 MM PITCH, ROHS COMPLIANT, PLASTIC, MS-026ABA, TQFP-32 |
| 文件頁數： | 27/50頁 |
| 文件大小： | 637K |
| 代理商： | AT42QT1111-AU |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
33
9571B–AT42–08/10
AT42QT1111-MU/AT42QT1111-AU
7.10
Address 6: Lower Burst Limit (LBL)
Normal QTouch signals are in the range of 100 to 1000 counts for each key. The lower burst
limit determines the minimum signal that is considered as a valid acquisition. If the count is lower
than the lower burst limit, it is considered not to be valid and the key is set to an Error state.
Note:
Where a key has a signal of less than the LBL, the key is set to its “no detect” state. If
the key signal rises above LBL, but remains under the detection level (that is: reference
signal - detection threshold), the Detect Integration is applied. In this case the detection
is not reported immediately but is delayed until the DI filter confirms detection.
Default value:
18
7.11
Addresses 7–8: AKS Mask
AKS_n (AKS Mask): 0 = key n AKS disabled, 1 = key n AKS enabled (where n is 0–10).
These bits control which keys have AKS enabled (see Section 3 on page 8). A “1” means the
corresponding key has AKS enabled; a “0” means that the corresponding key has AKS disabled.
Default AKS mask:
0x07 and 0xFF (all keys have AKS enabled)
7.12
Addresses 9–15: Detect0 – Detect6 PWM
Each of the 7 detect pins can be configured to output a PWM signal to indicate whether the key
is touched (in detect) or not touched (out of detect).
The Detect outputs must be enabled by selecting 7-key mode in the “Device Mode” setting (see
Section 7.4 on page 29), and the corresponding “Key to LED” bits must be set to enable the
individual “Detect” outputs for each key (see Section 7.14 on page 35).
Table 7-8.
Lower Burst Limit
Address
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
6LBL
Table 7-9.
AKS Mask
Address
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
7
AKS_10
AKS_9
AKS_8
8
AKS_7
AKS_6
AKS_5
AKS_4
AKS_3
AKS_2
AKS_1
AKS_0
Table 7-10.
Detect0 – Detect6 PWM
Address
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
9
IN_DETECT0
OUT_DETECT0
10
IN_DETECT1
OUT_DETECT1
11
IN_DETECT2
OUT_DETECT2
12
IN_DETECT3
OUT_DETECT3
13
IN_DETECT4
OUT_DETECT4
14
IN_DETECT5
OUT_DETECT5
15
IN_DETECT6
OUT_DETECT6
相關PDF資料 |
PDF描述 |
|---|---|
| AT76C453AC-MY19T | IMAGE SENSOR-CMOS, 708(H) X 494(V) PIXEL, 30fps, SURFACE MOUNT |
| ATF-33143-TR2 | X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET |
| ATF-33143-BLK | X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET |
| ATF-33143-TR1 | X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET |
| ATF-50189 | 0 MHz - 2400 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT42QT1111-AU QS383 | 制造商:Atmel Corporation 功能描述:QTOUCH 11 KEY TOUCH SENSOR IC |
| AT42QT1111MU | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:QTouch? 11-key Sensor IC |
| AT42QT1111-MU | 功能描述:電容觸摸傳感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
| AT42QT1111-MU QS384 | 制造商:Atmel Corporation 功能描述:QTOUCH 11 KEY TOUCH SENSOR IC |
| AT42QT1244-AU | 功能描述:電容觸摸傳感器 QMatrix FMEA 24 Key Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
發布緊急采購，3分鐘左右您將得到回復。