- 您現在的位置：買賣IC網 > PDF目錄67389 > AT42QT1111-AU (ATMEL CORP) PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | AT42QT1111-AU |
| 廠商： | ATMEL CORP |
| 元件分類： | 速度傳感器和接近開關 |
| 英文描述： | PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT |
| 封裝： | 7 X 7 MM, 1 MM HEIGHT, 0.80 MM PITCH, ROHS COMPLIANT, PLASTIC, MS-026ABA, TQFP-32 |
| 文件頁數： | 24/50頁 |
| 文件大小： | 637K |
| 代理商： | AT42QT1111-AU |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
30
9571B–AT42–08/10
AT42QT1111-MU/AT42QT1111-AU
REPEAT_TIME: selects the “repeat” time when “Timed” is selected as the trigger to start key
acquisition. The number entered is a multiple of 16 ms. If “0” is entered, the device will operate
in a continuous “free run” mode; that is, the QT1111 will not sleep after its cycle is completed but
will begin the next key acquisition cycle immediately.
Default KEY_AC value:
1 (timed)
Default MODE value:
0 (7-key mode)
Default SIGNAL value:
1 (parallel)
Default SYNC value:
1 (edge)
Default REPEAT_TIME value:
2 (32 ms cycle)
7.5
Address 1: Guard Key/Comms Options
GUARD_KEY: specifies the key (0 to 10) to be used as a guard channel (see Section 2.3 on
page 7) .
GD_EN: enables the use of a guard key; 0 = disable, 1 = enable.
SPI_EN: enables the Quick SPI interface; 0 = disable, 1 = enable.
See Section 4.1.6 on page 16 for details of the Quick SPI Mode report.
To exit this mode (and clear the “SPI_EN” bit), the command “0x36” should be sent. To save the
settings to EEPROM and make Quick SPI mode active on startup, send the “Store to EEPROM”
command (0x0A). Any other data sent is ignored in Quick SPI mode.
CHG: the CHANGE pin mode (see Section 4.5 on page 18):
0 = “Data” mode. In this mode the “Change” pin is asserted to indicate unread data.
1 = “Touch” mode. In this mode the “Change” pin is asserted when a key is being touched
or is in detect.
CRC: enables or disables CRC; 0 = disable, 1 = enable. When this option is enabled, each data
exchange must have a CRC byte appended.
When report or setup data is being returned by the QT1111, a 1-byte checksum is returned. The
host should confirm that this checksum is correct and, if not, should request the report again.
Where data is being sent by the host, a 1-byte CRC should be sent. The QT1111 returns the
expected CRC byte in the same transaction the CRC byte is sent. In this way, the host can
immediately determine whether the setup data bytes were received correctly.
If the host sends an incorrect CRC following a “Get” command, the QT1111 returns the code
“0xEE” to indicate an error. It then resets the SPI interface. On the next byte exchange 0x55 is
transmitted.
Default GUARD_KEY value:
0 (Key 0)
Default GD_EN value:
0 (disabled)
Default CHG value:
0 (data mode)
Default CRC value:
0 (disabled)
Table 7-3.
Guard Key/Comms Options
Address
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
1
GUARD_KEY
GD_EN
SPI_EN
CHG
CRC
相關PDF資料 |
PDF描述 |
|---|---|
| AT76C453AC-MY19T | IMAGE SENSOR-CMOS, 708(H) X 494(V) PIXEL, 30fps, SURFACE MOUNT |
| ATF-33143-TR2 | X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET |
| ATF-33143-BLK | X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET |
| ATF-33143-TR1 | X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET |
| ATF-50189 | 0 MHz - 2400 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT42QT1111-AU QS383 | 制造商:Atmel Corporation 功能描述:QTOUCH 11 KEY TOUCH SENSOR IC |
| AT42QT1111MU | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:QTouch? 11-key Sensor IC |
| AT42QT1111-MU | 功能描述:電容觸摸傳感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
| AT42QT1111-MU QS384 | 制造商:Atmel Corporation 功能描述:QTOUCH 11 KEY TOUCH SENSOR IC |
| AT42QT1244-AU | 功能描述:電容觸摸傳感器 QMatrix FMEA 24 Key Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
發布緊急采購，3分鐘左右您將得到回復。