參數資料
型號： AT42QT1110-MZ
廠商： ATMEL CORP
元件分類： 速度傳感器和接近開關
英文描述： PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT
封裝： 5 X 5 MM, 0.50 MM PITCH, ROHS COMPLIANT, MO-220VHHD-2, QFN-32
文件頁數： 38/46頁
文件大?。?/td> 657K
代理商： AT42QT1110-MZ
45
4519 Group
SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
WATCHDOG TIMER
Watchdog timer provides a method to reset the system when a pro-
gram run-away occurs. Watchdog timer consists of timer
WDT(16-bit binary counter), watchdog timer enable flag (WEF),
and watchdog timer flags (WDF1, WDF2).
The timer WDT downcounts the instruction clocks as the count
source from “FFFF16” after system is released from reset.
After the count is started, when the timer WDT underflow occurs
(after the count value of timer WDT reaches “000016,” the next
count pulse is input), the WDF1 flag is set to “1.”
If the WRST instruction is never executed until the timer WDT un-
derflow occurs (until timer WDT counts 65534), WDF2 flag is set to
“1,” and the RESET pin outputs “L” level to reset the microcom-
puter.
Execute the WRST instruction at each period of 65534 machine
cycle or less by software when using watchdog timer to keep the
microcomputer operating normally.
When the WEF flag is set to “1” after system is released from reset,
the watchdog timer function is valid.
When the DWDT instruction and the WRST instruction are ex-
ecuted continuously, the WEF flag is cleared to “0” and the
watchdog timer function is invalid.
However, in order to set the WEF flag to “1” again once it has
cleared to “0”, execute system reset.
The WRST instruction has the skip function. When the WRST in-
struction is executed while the WDF1 flag is “1”, the WDF1 flag is
cleared to “0” and the next instruction is skipped.
When the WRST instruction is executed while the WDF1 flag is “0”,
the next instruction is not skipped.
The skip function of the WRST instruction can be used even when
the watchdog timer function is invalid.
Fig. 32 Watchdog timer function
65534 count
(Note)
Value of 16-bit timer (WDT)
WDF1 flag
WRST instruction
executed
(skip executed)
RESET pin output
WDF2 flag
System reset
Reset
released
After system is released from reset (= after program is started), timer WDT starts count down.
When timer WDT underflow occurs, WDF1 flag is set to “1.”
When the WRST instruction is executed, WDF1 flag is cleared to “0,” the next instruction is skipped.
When timer WDT underflow occurs while WDF1 flag is “1,” WDF2 flag is set to “1” and the
watchdog reset signal is output.
The output transistor of RESET pin is turned “ON” by the watchdog reset signal and system reset is
executed.
Note: The number of count is equal to the number of cycle because the count source of watchdog timer
is the instruction clock.
FFFF16
000016
相關PDF資料
PDF描述
AT42QT1111-AU PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT
AT76C453AC-MY19T IMAGE SENSOR-CMOS, 708(H) X 494(V) PIXEL, 30fps, SURFACE MOUNT
ATF-33143-TR2 X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET
ATF-33143-BLK X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET
ATF-33143-TR1 X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET
相關代理商/技術參數
參數描述
AT42QT1111-AU 功能描述:電容觸摸傳感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍:
AT42QT1111-AU QS383 制造商:Atmel Corporation 功能描述:QTOUCH 11 KEY TOUCH SENSOR IC
AT42QT1111MU 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:QTouch? 11-key Sensor IC
AT42QT1111-MU 功能描述:電容觸摸傳感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍:
AT42QT1111-MU QS384 制造商:Atmel Corporation 功能描述:QTOUCH 11 KEY TOUCH SENSOR IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*