- 您現在的位置：買賣IC網 > PDF目錄67388 > AT42QT1070-SSU (ATMEL CORP) PROXIMITY SENSOR-CAPACITIVE, 0.6-2.6V, RECTANGULAR, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | AT42QT1070-SSU |
| 廠商： | ATMEL CORP |
| 元件分類： | 速度傳感器和接近開關 |
| 英文描述： | PROXIMITY SENSOR-CAPACITIVE, 0.6-2.6V, RECTANGULAR, SURFACE MOUNT |
| 封裝： | 0.150 INCH, ROHS COMPLIANT, PLASTIC, MS-012AB, SOIC-14 |
| 文件頁數： | 5/38頁 |
| 文件大小： | 509K |
| 代理商： | AT42QT1070-SSU |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
13
9596A–AT42–10/10
AT42QT1070
2.12.4
Max On Duration
If an object or material obstructs the sense pad the signal may rise enough to create a detection,
preventing further operation. To prevent this, the sensor includes a timer which monitors
detections. If a detection exceeds the timer setting the sensor performs a key recalibration. This
is known as the Max On duration feature and is set to approximately 30s in standalone mode.
In comms mode this feature can be changed by setting a value in the range 1 – 255
(160 ms – 40800 ms) in steps of 160 ms. A setting of 0 disables the Max On Duration
recalibration feature.
Note:
If bit 4 of address 53 is clear then a recalibration of all keys occurs on Max On Duration
instead of the individual key recalibration.
2.12.5
Positive Recalibration
If a keys signal jumps in the negative direction (with respect to its reference) by more than the
Positive Recalibration setting (4 counts), then a recalibration of that key takes place.
2.12.6
Drift Hold Time
Drift Hold Time (DHT) is used to restrict drift on all keys while one or more keys are activated.
DHT restricts the drifting on all keys until approximately four seconds after all touches have been
removed.
This feature is particularly useful in cases of high-density keypads where touching a key or
hovering a finger over the keypad would cause untouched keys to drift, and therefore create a
sensitivity shift, and ultimately inhibit touch detection.
2.12.7
Hysteresis
Hysteresis is fixed at 12.5 percent of the Detect Threshold. When a key enters a detect state
once the DI count has been reached, the NTHR value is changed by a small amount
(12.5 percent of NTHR) in the direction away from touch. This is done to affect hysteresis and so
makes it less likely a key will dither in and out of detect. NTHR is restored once the key drops out
of detect.
3.
Wiring and Parts
3.1
Rs Resistors
Series resistors Rs (Rs0 – Rs6 for comms mode and Rs0 – Rs4 for standalone mode) are in line
with the electrode connections and should be used to limit electrostatic discharge (ESD)
currents and to suppress radio frequency interference (RFI). Series resistors are recommended
for noise reduction. They should be approximately 4.7 k
to 20 k each.
3.2
LED Traces and Other Switching Signals
Digital switching signals near the sense lines induce transients into the acquired signals,
deteriorating the signal-to-noise (SNR) performance of the device. Such signals should be
routed away from the sensing traces and electrodes, or the design should be such that these
lines are not switched during the course of signal acquisition (bursts).
相關PDF資料 |
PDF描述 |
|---|---|
| AT42QT1110-AZ | PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT |
| AT42QT1110-MZ | PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT |
| AT42QT1111-AU | PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT |
| AT76C453AC-MY19T | IMAGE SENSOR-CMOS, 708(H) X 494(V) PIXEL, 30fps, SURFACE MOUNT |
| ATF-33143-TR2 | X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT42QT1070-SSU QS529 | 功能描述:IC TOUCH SENSOR 7KEY 14SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:QTouch™ 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AT42QT1070-SSUR | 功能描述:IC TOUCH SENSOR 7KEY 14SOIC 制造商:microchip technology 系列:QTouch?? 包裝:Digi-Reel? 零件狀態:在售 類型:按鈕 接近探測:無 輸入數:最高 7 LED 驅動器通道:最高 5 接口:I2C 分辨率:- 電壓 - 電源:1.8 V ~ 5.5 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:14-SOIC 標準包裝:1 |
| AT42QT1085-AU | 功能描述:電容觸摸傳感器 8 Channel QTouch Haptic Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
| AT42QT1085-AUR | 功能描述:電容觸摸傳感器 8 Channel QTouch Haptic Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
| AT42QT1085-MU | 功能描述:電容觸摸傳感器 8 Channel QTouch Haptic Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
發布緊急采購，3分鐘左右您將得到回復。