- 您現在的位置：買賣IC網 > PDF目錄364693 > APCI-SER4 PCI-BUS I/O CARD PDF資料下載
參數資料
| 型號： | APCI-SER4 |
| 英文描述： | PCI-BUS I/O CARD |
| 中文描述： | PCI總線的I / O卡 |
| 文件頁數： | 9/14頁 |
| 文件大?。?/td> | 251K |
| 代理商： | APCI-SER4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁
Page 9
2192-09125-000-000
J605 APCI-ADADIO
Full scale Gain Adjust
1) Set the input voltage to full scale positive minus 1 LSB
+4.9975 for the 5V range.
+9.9950 for the 10V range.
2) Adjust VR1 to give FFE to FFF.
Calibrating the DACs
In order to calibrate the DACs it is necessary to have a DVM with at least 5 digit resolution. On the
utility disk there is a
A single trimmer (VR2) is provided to adjust the reference voltage used by the DACs
Set the necessary links for the required mode and voltage ranges. Run the ADADIO.EXE program .
Measure the voltage between VREF (TP3) and AGND (TP9)and adjust VR2 until the reading is +5.02V.
Note:
- If the gain adjust trimmers (VR3-4) have insufficient range , adjust VR2 to read 5.01V, and
repeat the calibration procedure.
Unipolar Calibration - DAC Channel A
Zero Offset Adjust
1) Set DAC A output to 000 hex.
2) Measure the voltage between DAC A output and analogue ground and adjust VR5 to give 0.000V.
Full Scale Gain Adjust
1) Set DAC A output to 800 hex,
2) Measure the voltage between DAC A output and analogue ground and adjust VR3 to exactly half
scale output.
2.500V for the 0-5V range.
5.000V for the 0-10V range.
3) Set DAC A output to FFF hex and check output voltage is:-
4.9985 for the 0-5V range.
9.9975 for the 0-10V range.
4) Adjust VR3 if necessary.
Repeat for DAC B replacing VR5 with VR6, and VR3 with VR4.
Bipolar Calibration - DAC Channel A
Zero Offset Adjust
1) Set DAC A output to 000 hex.
2) Measure the voltage between DAC A output and analogue ground and adjust VR5 to give full scale
negative i.e -5.000V.
Full Scale Gain Adjust
1) Set the DAC A output to 800 hex.
2) Measure the voltage between DAC A output and analogue ground and adjust VR3 to give half
scale output i.e 0.000V.
3) Set DAC A to FFF hex and check full scale is 4.9975V.
Repeat for DAC channel B replacing VR5 with VR6, and VR3 with VR4.
相關PDF資料 |
PDF描述 |
|---|---|
| APD1510-000 | APD Series:Silicon PIN Diode Chips|PIN Diodes: General Purpose Switching PIN Diodes |
| APD1520-000 | APD Series:Silicon PIN Diode Chips|PIN Diodes: General Purpose Switching PIN Diodes |
| APD2520CGCK03 | 4.5x2mm SMD CHIP LED LAMP |
| APD2520EC03 | 4.5x2mm SMD CHIP LED LAMP |
| APD2520MBC03 | 4.5x2mm SMD CHIP LED LAMP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| APCITE | 制造商:Pentair Technical Products / Hoffman 功能描述:Operator Adapter, I.T.E. , for I-T-E Max-Flex, Steel |
| APCMB012 | 制造商:Amphenol Corporation 功能描述:MS3106E24-AJP W/OUT CNTS |
| APCMB108 | 制造商:Amphenol RF 功能描述: |
| APCMB109-M4 | 制造商:Amphenol Corporation 功能描述:MS3102E18-3P TAPPED M4 |
| APCMB111 | 制造商:Amphenol Corporation 功能描述:CONNECTOR |
發布緊急采購，3分鐘左右您將得到回復。