ProASICPLUS Flash Family FPGAs 2- 10 v5.9 Timing Control and Characteristics
參數資料
型號： APA075-TQ144I
廠商： Microsemi SoC
文件頁數： 92/178頁
文件大?。?/td> 0K
描述： IC FPGA PROASIC+ 75K 144-TQFP
標準包裝： 60
系列： ProASICPLUS
RAM 位總計： 27648
輸入/輸出數： 107
門數： 75000
電源電壓： 2.3 V ~ 2.7 V
安裝類型： 表面貼裝
工作溫度： -40°C ~ 85°C
封裝/外殼： 144-LQFP
供應商設備封裝： 144-TQFP（20x20）
ProASICPLUS Flash Family FPGAs
2- 10
v5.9
Timing Control and
Characteristics
ProASICPLUS Clock Management System
ProASICPLUS devices provide designers with very flexible
clock conditioning capabilities. Each member of the
ProASICPLUS family contains two phase-locked loop (PLL)
blocks which perform the following functions:
Clock Phase Adjustment via Programmable Delay
(250 ps steps from –7 ns to +8 ns)
Clock Skew Minimization
Clock Frequency Synthesis
Each PLL has the following key features:
Input Frequency Range (fIN) = 1.5 to 180 MHz
Feedback Frequency Range (fVCO) = 24 to 180 MHz
Output Frequency Range (fOUT) = 8 to 180 MHz
Output Phase Shift = 0 ° and 180 °
Output Duty Cycle = 50%
Low Output Jitter (maximum at 25°C)
–fVCO <10 MHz. Jitter ±1% or better
–
10 MHz < fVCO < 60 MHz. Jitter ±2% or better
–fVCO > 60 MHz. Jitter ±1% or better
Note: Jitter (ps) = Jitter (%) × period
For Example:
Low Power Consumption – 6.9 mW (max. – analog
supply) + 7.0 W/MHz (max. – digital supply)
Physical Implementation
Each side of the chip contains a clock conditioning circuit
based on a 180 MHz PLL block (Figure 2-11 on page
2-11). Two global multiplexed lines extend along each
side of the chip to provide bidirectional access to the PLL
on that side (neither MUX can be connected to the
opposite side's PLL). Each global line has optional LVPECL
input pads (described below). The global lines may be
driven by either the LVPECL global input pad or the
outputs from the PLL block, or both. Each global line can
be driven by a different output from the PLL. Unused
global pins can be configured as regular I/Os or left
unconnected. They default to an input with pull-up. The
two signals available to drive the global networks are as
Global A (secondary clock)
Output from Global MUX A
Conditioned version of PLL output (fOUT) – delayed
or advanced
Divided version of either of the above
Further delayed version of either of the above
(0.25 ns, 0.50 ns, or 4.00 ns delay)1
Global B
Output from Global MUX B
Delayed or advanced version of fOUT
Divided version of either of the above
Further delayed version of either of the above
(0.25 ns, 0.50 ns, or 4.00 ns delay)2
Functional Description
Each PLL block contains four programmable dividers as
shown in Figure 2-11 on page 2-11. These allow
frequency scaling of the input clock signal as follows:
The n divider divides the input clock by integer
factors from 1 to 32.
The m divider in the feedback path allows
multiplication of the input clock by integer factors
ranging from 1 to 64.
The two dividers together can implement any
combination
of
multiplication
and
division
resulting in a clock frequency between 24 and 180
MHz exiting the PLL core. This clock has a fixed
50% duty cycle.
The output frequency of the PLL core is given by
the formula in EQ 2-1 (fREF is the reference clock
frequency):
fOUT = fREF × m ÷ n
EQ 2-1
The third and fourth dividers (u and v) permit the
signals applied to the global network to each be
further divided by integer factors ranging from 1
to 4.
The implementations shown in EQ 2-2 and EQ 2-3 enable
the user to define a wide range of frequency multiplier
and divisors.
EQ 2-2
EQ 2-3
Jitter in picoseconds at 100 MHz = 0.01 × (1/100E6) = 100 ps
Maximum Acquisition
Time
= 80 s for fVCO > 40 MHz
= 30 s for fVCO < 40 MHz
1. This mode is available through the delay feature of the global MUX driver.
f
GLB
m
nu
×
()
-----------------
=
f
GLA
m
nv
×
()
-----------------
=
相關PDF資料
PDF描述
ABC43DRYH-S93 CONN EDGECARD 86POS DIP .100 SLD
A42MX09-PLG84A IC FPGA MX SGL CHIP 14K 84-PLCC
ESC65DRTS-S734 CONN EDGECARD 130PS DIP .100 SLD
EMC49DRAS CONN EDGECARD 98POS R/A .100 SLD
A42MX09-PQG160 IC FPGA MX SGL CHIP 14K 160-PQFP
相關代理商/技術參數
參數描述
APA075-TQ896A 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:Automotive-Grade ProASIC Flash Family FPGAs
APA075-TQB 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:ProASIC Flash Family FPGAs
APA075-TQES 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:ProASIC Flash Family FPGAs
APA075-TQG100 功能描述:IC FPGA PROASIC+ 75K 100-TQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:ProASICPLUS 標準包裝:152 系列:IGLOO PLUS LAB/CLB數:- 邏輯元件/單元數:792 RAM 位總計:- 輸入/輸出數:120 門數:30000 電源電壓:1.14 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C 封裝/外殼:289-TFBGA，CSBGA 供應商設備封裝:289-CSP（14x14）
APA075-TQG100A 功能描述:IC FPGA PROASIC+ 75K 100-TQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:ProASICPLUS 標準包裝:90 系列:ProASIC3 LAB/CLB數:- 邏輯元件/單元數:- RAM 位總計:36864 輸入/輸出數:157 門數:250000 電源電壓:1.425 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 125°C 封裝/外殼:256-LBGA 供應商設備封裝:256-FPBGA（17x17）
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*