- 您現在的位置：買賣IC網 > PDF目錄375327 > AN8029 (PANASONIC CORP) Self-excited RCC pseudo-resonance type AC-DC switching power supply control IC PDF資料下載
參數資料
| 型號： | AN8029 |
| 廠商： | PANASONIC CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Self-excited RCC pseudo-resonance type AC-DC switching power supply control IC |
| 中文描述： | 1 A SWITCHING CONTROLLER, PSIP9 |
| 封裝： | PLASTIC, SIP-9 |
| 文件頁數： | 9/13頁 |
| 文件大?。?/td> | 132K |
| 代理商： | AN8029 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁
9
Voltage Regulators
AN8029
I
Application Notes (continued)
[1] Operation descriptions (continued)
6. Overcurrent protection circuit (continued)
The R6 and C6 in figure 7 construct the filter circuit for removing the
noise generated by the parasitic capacitance equivalently accompanied
when turning on the power MOSFET. For overcurrent detection resis-
tance R7, the carbon resistor should be used but not the wire winding
resistor, because the high-frequency current flows in it.
Notes on the detection level precision
This overcurrent detection level reflects on the operating current level of the power supply overcurrent
protection. Therefore, if this detection level fluctuates with temperature or variability, the operating current level
of the overcurrent protection of power supply itself also fluctuates. Since such level fluctuation means the neces-
sity for an increase in the withstanding capability of used parts and in the worst case it means the cause of
destruction, the accuracy of detection level is increased as much as possible for the AN8029 (approximately
±
4%).
7. Overvoltage protection circuit (OVP)
OVP is an abbreviation of over voltage protection. It refers to a self-diagnosis function, which stops the power
supply to protect the load when the power supply output generates abnormal voltage higher than the normal
output voltage due to failure of the control system or an abnormal voltage applied from the outside. (Refer to
figure 8.)
Figure 7
C6
R8
CLM
GND
R6
R7
Figure 8
Abnormal voltage applied
from outside
Power supply output
Load
It detects abnormal voltage applied from the outside
to the power supply output (the voltage which is higher than
voltage of the power supply output and may damage the load)
by the primary side of the bias coil and operates the OVP.
GND
Start resistor
R1
V
CC
TIM/OVP
V
OUT
After AC rectification
FRD
Basically, it is set to monitor the voltage of supply voltage V
CC
terminal of the IC. Normally, the V
CC
voltage
is supplied from the transformer drive coil. Since this voltage is proportional to the secondary side output voltage,
it still operates even when the secondary side output is in overvoltage.
1) When the voltage input to the OVP terminal exceeds the threshold voltage (7.3 V typical) as the result of
power supply output abnormality, the protective circuit shuts down the internal reference voltage of the IC to
stop all of the controls and keeps this stop condition.
2) The OVP reset is done by decreasing the supply voltage (V
CC
<
8.2 V typical: OVP release supply voltage).
(1) When the supply voltage becomes lower than the stop voltage,
(2) When the supply voltage becomes lower than the OVP release voltage,
The discharge circuit is incorporated so that the electric charge which is charged in the capacitor connected to
the OVP terminal can be discharged momentarily for the next re-start.
secondary side output voltage under normal operation V
OUT
V
CC
terminal voltage under normal operation
V
7
=
V
th(OVP)
+
V
Z
V
th(OUT)
: Secondary side output overvoltage threshold value
V
th(OVP)
: OVP operation threshold value
V
Z
: Zener voltage (externally attached to OVP terminal)
V
th(OUT)
=
×
V
7
相關PDF資料 |
PDF描述 |
|---|---|
| AN8031 | Active filter control IC |
| AN8032 | Active filter control IC |
| AN8038S | AC-DC switching power supply control IC with RCC local resonance circuit for improved conformance with energy conservation laws |
| AN8041S | Liquid crystal backlight control IC |
| AN8049 | 1.8-volt 3-channel step-up, step-down, and polarity inverting DC-DC converter control IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AN8031 | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:Active filter control IC |
| AN8031-6-080 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| AN8031AH | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| AN8032 | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:Active filter control IC |
| AN8032AH | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。