- 您現在的位置：買賣IC網 > PDF目錄375327 > AN8013SH (PANASONIC CORP) Single-channel step-up or step-down DC-DC converter control IC PDF資料下載
參數資料
| 型號： | AN8013SH |
| 廠商： | PANASONIC CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Single-channel step-up or step-down DC-DC converter control IC |
| 中文描述： | 0.1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封裝： | SSOP-10 |
| 文件頁數： | 8/15頁 |
| 文件大?。?/td> | 125K |
| 代理商： | AN8013SH |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
AN8013SH
Voltage Regulators
8
I
Application Notes
[2] Function descriptions
1. Reference voltage block
The reference voltage block is based on a band gap circuit, and outputs a temperature corrected reference
voltage of 2.5 V. This reference voltage is stabilized once the supply voltage exceeds 3.6 V, and is used as the
power supply for the IC itself.
2. Triangular wave generator
This circuit generates a triangular wave with a peak of about 1.45 V and a trough of about 0.35 V using a timing
capacitor connected to the CT pin (pin 3) and a timing resistor connected to the RT pin (pin 2) respectively. The
oscillator frequency can be set to arbitrary value by selecting appropriate values for the external capacitor and
resistor, C
T
and R
T
. The triangular wave signal is provided to the inverting input the PWM comparator internally
to the IC.
3. Error amplifier
This circuit is an PNP-transistor input error ampli-
fier that detects and amplifies the DC-DC converter
output voltage, and inputs that signal to a PWM com-
parator.
A 0.75 V level is created by resistors dividing the
internal reference voltage. This level is applied to the
noninverting input.
Arbitrary gain and phase compensation can be set
up by inserting a resistor and capacitor in series
between the error amplifier output pin (pin 6) and the
inverting input pin (pin 7).
The output voltage V
OUT
is given by the following
formula by connecting a resistor divider to the output
as shown in figure 1.
R1
+
R2
R
2
4. Timer latch short-circuit protection circuit
This circuit protects the external main switching element, flywheel diode, choke coil, and other components
against degradation or destruction if an excessive load or a short circuit of the power supply output continues for
longer than a certain fixed period.
The timer latch short-circuit protection circuit detects the output of the error amplifier. If the DC-DC converter
output voltage drops and an error amplifier output level exceeds 1.90 V, this circuit outputs a low level and the
timer circuit starts. This starts charging the external protection circuit delay time capacitor.
If the error amplifier output does not return to the normal voltage range before that capacitor reaches 0.75 V,
the latch circuit latches, the output drive transistors are turned off, and the dead-time is set to 100%.
V
OUT
= 0.75
×
5. Low input voltage malfunction prevention circuit (U.V.L.O.)
This circuit protects the system against degradation or destruction due to incorrect control operation when the
power supply voltage falls during power on or power off.
The low input voltage malfunction prevention circuit detects the internal reference voltage that changes with
the supply voltage level. While the supply voltage is rising, this circuit cuts off the output drive transistor until the
reference voltage reaches 3.1 V. It also sets the dead-time to 100%, and at the same time holds the S.C.P. pin (pin
4) at the low level. During the fall time of the power supply voltage, it has hysteresis width of 200 mV and operates
2.9 V or less.
V
OUT
Error amp.
R1
R3
R4
R2
R
N
PWM
comparator
input
0.75 V
Internal 2.5 V
reference voltage
C
N
IN
FB
Figure 1. Connection method of error amplifier
6
7
相關PDF資料 |
PDF描述 |
|---|---|
| AN8016 | Single-channel 1.8-volt step-up DC-DC converter control IC |
| AN8016NSH | Single-channel 1.8-volt step-up DC-DC converter control IC |
| AN8017SA | 1.8-volt 2-channel step-up DC-DC converter control IC |
| AN8021SB | AC-DC switching power supply control IC |
| AN8021NS | External excitation flyback AC-DC switching power supply control IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AN8013SH-E1 | 功能描述:IC REG BUCK BST ADJ 0.1A 10SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:High Efficiency Current Mode Switching Regulators CMOS LDO Regulators 特色產品:BD91x Series Step-Down Regulators 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:兩者兼有 輸出數:2 輸出電壓:3.3V，0.8 V ~ 2.5 V 輸入電壓:4.5 V ~ 5.5 V PWM 型:電流模式 頻率 - 開關:1MHz 電流 - 輸出:1.5A 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:VQFN020V4040 產品目錄頁面:1373 (CN2011-ZH PDF) 其它名稱:BD9152MUV-E2TR |
| AN8013SH-E1V | 功能描述:IC REG BUCK BST ADJ 0.1A 10SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:High Efficiency Current Mode Switching Regulators CMOS LDO Regulators 特色產品:BD91x Series Step-Down Regulators 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:兩者兼有 輸出數:2 輸出電壓:3.3V，0.8 V ~ 2.5 V 輸入電壓:4.5 V ~ 5.5 V PWM 型:電流模式 頻率 - 開關:1MHz 電流 - 輸出:1.5A 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:VQFN020V4040 產品目錄頁面:1373 (CN2011-ZH PDF) 其它名稱:BD9152MUV-E2TR |
| AN8014 | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:Step-down, step-up, or inverting DC-DC converter control IC |
| AN8014S | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:Step-down, step-up, or inverting DC-DC converter control IC |
| AN8014S-E1 | 功能描述:IC REG CTRLR BST INV PWM SO16 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。