- 您現在的位置：買賣IC網 > PDF目錄378404 > AN49.0 (Intersil Corporation) Circular Connector; No. of Contacts:11; Series:MS27656; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Pin; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:19-11 RoHS Compliant: No PDF資料下載
參數資料
| 型號： | AN49.0 |
| 廠商： | Intersil Corporation |
| 元件分類： | 圓形連接器 |
| 英文描述： | Circular Connector; No. of Contacts:11; Series:MS27656; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Pin; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:19-11 RoHS Compliant: No |
| 中文描述： | 數字音頻放大器增益控制使用對數 |
| 文件頁數： | 1/2頁 |
| 文件大?。?/td> | 155K |
| 代理商： | AN49.0 |
1
AN49.0
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-352-6832
Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2005. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
Digital Audio Amplifier Gain Control using Logarithmic
Intersil Digitally Controlled Potentiontiometers (XDCPs)
Often the power amplifier stage of a communications device
is located some distance from the control panel. The typical
solution is to mount the volume control on the front panel
and run a pair of shielded cables back to the power amplifier
stage. A better solution is to use the Intersil X9314
logarithmic taper digitally controlled potentiometer. This
completely eliminates the need for shielded cables since the
digital pot can be located on the printed circuit board near
the low level input stages of the power amplifier. The
up/down volume switches can be located yards away as
these are merely low speed TTL signals.
Circuit Description
Figure 1 shows the X9314 with the low voltage LM386 power
amplifier. This circuit will produce 250mW of audio power
with only a 5V DC source. Figure 2 is a similar circuit that
uses the higher power LM380 and is capable of delivering
over 1W of audio if a 12V DC source is available. Either
circuit will provide plenty of sound for intercom,
communications, or monitoring applications. The 1W circuit
would be preferred when higher ambient noise is present,
such as in an automobile.
A 74HC132 quad Schmitt nand gate (U2) plus a few
discretes are all that are required to interface to U1, the
X9314W 10k
XDCP. When either pushbutton switch, S1 or
S2, is depressed, U2A output will be HIGH. This immediately
brings U2B output LOW which enables the XDCP. After a
short delay determined by R3 and C3, the astable
multivibrator (U2C) will begin generating increment pulses.
The frequency of the oscillation (and consequently the
speed at which the volume can be controlled) is determined
by C1 and R1. The values shown will advance the X9314
through all 32 wiper taps in about 5 seconds. R1 can be
changed from 5KW to 1MW to suit your preference. When
the pushbutton switches are released, R2 and C2 delay the
release of the X9314 chip select in order to ensure that the
last increment pulse is written.
The X9314W needs little else to apply it to most audio
circuits, but C9 has been included here to remove any DC
component that may be present on the input signal. Also,
lowpass filter R7 and C8 removes residual high frequency
noise from the digital pots’ internal charge pumps.
The LM380 and LM386 power amplifiers have fixed gains of
34dB and 26dB respectively. The gain of the LM386 can be
increased to 46dB (X200) by connecting a 10μF capacitor
from pins 1 to 8. The positive pole of the capacitor should be
connected to pin 1. The output snubber network (R6 and C5)
is required for stability and should be located close to the
output pin of the power amplifier. These amplifiers have fairly
high gain and wide bandwidths, so be careful with PCB trace
lengths. All connections to these amplifiers should be as
short and direct as possible.
Application Note
Author: Applications Staff
April 21, 2005
相關PDF資料 |
PDF描述 |
|---|---|
| AN535 | PHASE LOCKED LOOP DESIGN FUNDAMENTALS |
| AN540 | Implementing IIR Digital Filters |
| AN5766 | 8MHz Power Amps For Military, Industrial and Commercial Equipment |
| AN597 | Implementing Ultrasonic Ranging |
| an6077 | An IC Operational Transconductance Amplifier With Power Capability |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AN490HT6P | 制造商:AN# - MILITARY 功能描述: |
| AN4999 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Turn-on of thyristors in parallel |
| AN4C10A | 制造商:AN# - MILITARY 功能描述: |
| AN4C12A | 制造商:AN# - MILITARY 功能描述: |
| AN4C13A | 制造商:AN# - MILITARY 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。