參數資料
型號: AMIS42673ICAG1RG
廠商: ON Semiconductor
文件頁數: 7/11頁
文件大小: 0K
描述: TRANSCEIVER CAN HS 3.3V 8SOIC
標準包裝: 1
類型: 收發(fā)器
驅動器/接收器數: 1/1
規(guī)程: CAN
電源電壓: 4.75 V ~ 5.25 V
安裝類型: 表面貼裝
封裝/外殼: 8-SOIC(0.154",3.90mm 寬)
供應商設備封裝: 8-SOICN
包裝: 標準包裝
產品目錄頁面: 1115 (CN2011-ZH PDF)
其它名稱: 766-1008-6
AMIS42673
http://onsemi.com
5
FUNCTIONAL DESCRIPTION
General
The AMIS42673 is the interface between the CAN
protocol controller and the physical bus. It is intended for
use in industrial and automotive applications requiring baud
rates up to 1 Mbit/s. It provides differential transmit
capability to the bus and differential receiver capability to
the CAN protocol controller. It is fully compatible to the
“ISO 118982” standard.
Operating Modes
AMIS42673 only operates in highspeed mode as
illustrated in Table 5.
The transceiver is able to communicate via the bus lines.
The signals are transmitted and received to the CAN
controller via the pins TxD and RxD. The slopes on the bus
lines outputs are optimized to give extremely low EME.
Table 5. FUNCTIONAL TABLE OF AMIS42673; x = don’t care
VCC
Pin TxD
Pin CANH
Pin CANL
Bus State
Pin RxD
4.75 to 5.25 V
0
High
Low
Dominant
0
4.75 to 5.25 V
1
(or floating)
VCC/2
Recessive
1
VCC < PORL (Unpowered)
x
0 V < CANH < VCC
0 V < CANL < VCC
Recessive
1
PORL < VCC < 4.75 V
> 2 V
0 V < CANH < VCC
0 V < CANL < VCC
Recessive
1
Overtemperature Detection
A thermal protection circuit protects the IC from damage
by switching off the transmitter if the junction temperature
exceeds a value of approximately 160
°C. Because the
transmitter dissipates most of the power, the power
dissipation and temperature of the IC is reduced. All other
IC functions continue to operate. The transmitter offstate
resets when Pin TxD goes HIGH. The thermal protection
circuit is particularly needed when a bus line short circuits.
High Communication Speed Range
The transceiver is primarily intended for industrial
applications. It allows very low baud rates needed for long
bus length applications. But also high speed communication
is possible up to 1 Mbit/s.
FailSafe Features
A currentlimiting circuit protects the transmitter output
stage from damage caused by accidental shortcircuit to
either positive or negative supply voltage although power
dissipation increases during this fault condition.
The pins CANH and CANL are protected from
automotive electrical transients (according to “ISO 7637”;
see Figure 3).
Should TxD become disconnected, this pin is pulled high
internally.
When the VCC supply is removed, Pins TxD and RxD will
be floating. This prevents the AMIS42673 from being
supplied by the CAN controller through the I/O Pins.
3.3 V Interface
AMIS42673 may be used to interface with 3.3 V or 5 V
controllers by use of the V33 pin. This pin may be supplied
with 3.3 V or 5 V to have the corresponding digital interface
voltage levels.
When the V33 pin is supplied at 2.5 V, even interfacing
with 2.5 V CAN controllers is possible. See also Digital
Output Characteristics @ V33 = 2.5 V, Table . In this case a
pullup resistor from TxD to V33 is necessary.
相關PDF資料
PDF描述
IDT72V3662L15PF8 IC FIFO 8192X36 15NS 120QFP
MS3111P14-12P CONN RCPT 12POS CBL MNT W/PINS
IDT72805LB15BG8 IC FIFO SYNC DUAL 256X18 121BGA
V48B28M250BL2 CONVERTER MOD DC/DC 28V 250W
IDT723631L15PF IC FIFO SYNC 512X36 120-TQFP
相關代理商/技術參數
參數描述
AMIS-42675 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High Speed Low Power CAN Transceiver for Long Wire Networks
AMIS-42675AGA 制造商:AMI 制造商全稱:AMI 功能描述:High-Speed Low Power CAN Transceiver
AMIS42675ICAA1G 功能描述:CAN 接口集成電路 HS LOW POWER TRANSCEIVER RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
AMIS42675ICAA1RG 功能描述:CAN 接口集成電路 HS LOW POWER TRANSCEIVER RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
AMIS42675ICAAIG 制造商:ON Semiconductor 功能描述: