- 您現在的位置：買賣IC網 > PDF目錄10701 > AMIS41682CANM1RG (ON Semiconductor)TRANSCEIVER CAN FT LO PWR 14SOIC PDF資料下載
參數資料
| 型號： | AMIS41682CANM1RG |
| 廠商： | ON Semiconductor |
| 文件頁數： | 14/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | TRANSCEIVER CAN FT LO PWR 14SOIC |
| 標準包裝： | 1 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | CAN |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOICN |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 1115 (CN2011-ZH PDF) |
| 其它名稱： | 766-1005-6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁
AMIS41682, AMIS41683
http://onsemi.com
7
Local Wakeup: Rising or falling edge on input WAKE
(levels maintained for a certain period).
Remote Wakeup from CAN Bus: A message with five
consecutive dominant bits.
On a wakeup request the transceiver will set the output
on Pin INH high which can be used to activate the external
supply voltage regulator. Note: Pin INH is also set similarly
as an after wake up event by VBAT voltage being below the
battery power on flag level. (See FLAG_VBAT in Figure 5)
If VCC is provided, the wakeup request can be read on the
ERR or RXD outputs so the external microcontroller can
wakeup the transceiver (switch to normal operating mode)
via Pins STB and EN.
In the low power modes the failure detection circuit
remains partly active to prevent increased power
consumption in the event of failures 3, 3a, 4, and 7.
The gotosleepmode is only a transition mode. The Pin
INH stays active for a limited time. During this time the
circuit can still go to another lowpower mode. After this
time the circuit goes to the sleepmode. In case of a wake up
request (from BUS or WAKE Pin) during this transition
time, the wakeup request has higher priority than
gotosleepand INH will not be deactivated.
Behavior in Case of Missing Supplies
If VCC is below the threshold level FLAG_VCC, the signals
on pins STB and EN will internally be set to low-level to
provide fail safe functionality. In this way, a low-power mode
will be forced in case of missing/failing VCC supply.
Similarly, missing/failing VBAT supply – i.e. VBAT being
below FLAG_VBAT level - will lead to a fail-safe behavior of
the transceiver by forcing a low-power mode.
A forced low-power in case of missing supplies
guarantees that the transceiver will in no way disturb the
other CAN nodes when the local electronic unit looses
ground or battery connection.
STB change state
PowerOn Standby
High Low Act
EN change state
STB change state
1) Only when Vcc > POR_Vcc
2) INH active for a time = T_GoToSleep
3) Local Wakeupthrough pin Wake which change state
for a time > T_wake_min
Remote Wakeup through pin CANL or CANH when
dominant for a time >TCANH_min or TCANL_min
4) Mode Change through pins STB and EN is only
possible if Vcc > POR_Vcc
STB
ERR
RxD
INH
EN
RTL
POR
flag
WU
int
Vbat
Normal Mode
High High Act
STB
ERR
RxD
INH
EN
RTL
Err
flag
Rec.
out
Vcc
Standby Mode
Low Low Act
STB
ERR
RxD
INH
EN
RTL
Vbat
GoTo Sleep Mode
Low High Act
2)
STB
ERR
RxD
INH
EN
RTL
Vbat
Sleep Mode
Low Low
Hz
STB
ERR
RxD
INH
EN
RTL
Vbat
WU
int
WU
int
WU
int
WU
int
WU
int 1)
WU
int 1)
EN change state
EN, STB change state
Timeout GoToSleep mode
Local or Remote
Wakeup 3)
PowerOn
Mode Change 4)
Figure 5. Low Power Modes
PowerOn
After poweron (VBAT switched on) the signal on Pin INH
will become high and an internal poweron flag will be set.
This flag can be read in the poweron standby mode via pin
ERR (STB = 1; EN = 0) and will be reset by entering the
normal operating mode.
Protections
A current limiting circuit protects the transmitter output
stages against short circuit to positive and negative battery
voltage. If the junction temperature exceeds a maximum
value, the transmitter output stages are disabled and flagged
on the ERR pin. Because the transmitter is responsible for
the major part of the power dissipation, this will result in
reduced power dissipation and hence a lower chip
temperature. All other parts of the IC will remain operating.
The Pins CANH and CANL are protected against
electrical transients that may occur in an automotive
environment.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-25P-MY-B1 | CONVERTER MOD DC/DC 13.8V 50W |
| ADS7825P | IC MUX 16-BIT 4CH A/D 28-DIP |
| VI-204-MY-B1 | CONVERTER MOD DC/DC 48V 50W |
| LTC6702HTS8#TRPBF | IC COMP LOW VOLT TSOT23-8 |
| VI-243-MY-B1 | CONVERTER MOD DC/DC 24V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMIS41682NGA | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Fault Tolerant CAN Transceiver |
| AMIS-41683 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Fault Tolerant CAN Transceiver |
| AMIS41683CANN1G | 功能描述:CAN 接口集成電路 LS FT CAN TRANSC (3.3V) RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| AMIS41683CANN1RG | 功能描述:CAN 接口集成電路 LS FT CAN TRANSC 3.3V RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| AMIS-4168X | 制造商:AMI 制造商全稱:AMI 功能描述:Fault Tolerant CAN Transceiver |
發布緊急采購，3分鐘左右您將得到回復。