參數資料
型號: AMIS41682CANM1RG
廠商: ON Semiconductor
文件頁數: 12/16頁
文件大?。?/td> 0K
描述: TRANSCEIVER CAN FT LO PWR 14SOIC
標準包裝: 1
類型: 收發器
驅動器/接收器數: 1/1
規程: CAN
電源電壓: 4.75 V ~ 5.25 V
安裝類型: 表面貼裝
封裝/外殼: 14-SOIC(0.154",3.90mm 寬)
供應商設備封裝: 14-SOICN
包裝: 標準包裝
產品目錄頁面: 1115 (CN2011-ZH PDF)
其它名稱: 766-1005-6
AMIS41682, AMIS41683
http://onsemi.com
5
FUNCTIONAL DESCRIPTION
Description
AMIS41682 is a fault tolerant CAN transceiver which
works as an interface between the CAN protocol controller
and the physical wires of the CAN bus (see Figure 2). It is
primarily intended for low speed applications, up to 125 kB,
in passenger cars. The device provides differential transmit
capability to the CAN bus and differential receive capability
to the CAN controller.
The AMIS41683 has opendrain outputs (RXD and
ERR Pins), which allow the user to use external pullup
resistors to the required supply voltage; this can be 5 V or
3.3 V.
To reduce EME, the rise and fall slope are limited.
Together with matched CANL and CANH output stages,
this allows the use of an unshielded twisted pair or a parallel
pair of wires for the bus lines.
The failure detection logic automatically selects a suitable
transmission mode, differential or singlewire transmission.
Together with the transmission mode, the failure detector
will configure the output stages in such a way that excessive
currents are avoided and the circuit returns to normal
operation when the error is removed.
A high commonmode range for the differential receiver
guarantees reception under worst case conditions and
together with the integrated filter the circuit realizes an
excellent immunity against EMS. The receivers connected
to pins CANH and CANL have threshold voltages that
ensure a maximum noise margin in singlewire mode.
A timer has been integrated at Pin TXD. This timer
prevents the AMIS41682 from driving the bus lines to a
permanent dominant state.
Failure Detector
The failure detector is fully active in the normal operating
mode. After the detection of a single bus failure the detector
switches to the appropriate mode. The different wiring
failures are depicted in Figure 4. The figure also indicates
the effect of the different wiring failures on the transmitter
and the receiver. The detection circuit itself is not depicted.
The differential receiver threshold voltage is typically set
at 3 V (VCC = 5 V). This ensures correct reception with a
noise margin as high as possible in the normal operating
mode and in the event of failures 1, 2, 4, and 6a. These
failures, or recovery from them, do not destroy ongoing
transmissions. During the failure, reception is still done by
the differential receiver and the transmitter stays fully
active.
To avoid false triggering by external RF influences the
singlewire modes are activated after a certain delay time.
When the bus failure disappears for another time delay, the
transceiver switches back to the differential mode. When
one of the bus failures 3, 5, 6, 6a, and 7 is detected, the
defective bus wire is disabled by switching off the affected
bus termination and the respective output stage. A wakeup
from sleep mode via the bus is possible either by way of a
dominant CANH or CANL line. This ensures that a
wakeup is possible even if one of the failures 1 to 7 occurs.
If any of the wiring failure occurs, the output signal on pin
ERR will become low. On error recovery, the output signal
on pin ERR will become high again.
During all singlewire transmissions, the EMC
performance (both immunity and emission) is worse than in
the differential mode. The integrated receiver filters
suppress any HF noise induced into the bus wires. The
cutoff frequency of these filters is a compromise between
propagation delay and HF suppression. In the singlewire
mode, LF noise cannot be distinguished from the required
signal.
相關PDF資料
PDF描述
VI-25P-MY-B1 CONVERTER MOD DC/DC 13.8V 50W
ADS7825P IC MUX 16-BIT 4CH A/D 28-DIP
VI-204-MY-B1 CONVERTER MOD DC/DC 48V 50W
LTC6702HTS8#TRPBF IC COMP LOW VOLT TSOT23-8
VI-243-MY-B1 CONVERTER MOD DC/DC 24V 50W
相關代理商/技術參數
參數描述
AMIS41682NGA 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Fault Tolerant CAN Transceiver
AMIS-41683 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Fault Tolerant CAN Transceiver
AMIS41683CANN1G 功能描述:CAN 接口集成電路 LS FT CAN TRANSC (3.3V) RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
AMIS41683CANN1RG 功能描述:CAN 接口集成電路 LS FT CAN TRANSC 3.3V RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
AMIS-4168X 制造商:AMI 制造商全稱:AMI 功能描述:Fault Tolerant CAN Transceiver