- 您現在的位置：買賣IC網 > PDF目錄364674 > AMIS-52100 Transceiver with Clock and Data Recovery PDF資料下載
參數資料
| 型號： | AMIS-52100 |
| 英文描述： | Transceiver with Clock and Data Recovery |
| 中文描述： | 收發器時鐘和數據恢復 |
| 文件頁數： | 20/26頁 |
| 文件大小： | 1040K |
| 代理商： | AMIS-52100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁
AMIS-52100
Low-Power Transceiver with Clock and Data Recovery
Data Sheet
Table 26: Auto Slice Control Registers
Auto Slice Control Registers
Register (HEX)
0x0a
Name
DATA SLICE
THRESHOLD
HYSTERESIS
Bits
All
States
Comments
Set a fixed reference level for the slice output to be
compared to in the DAC mode
0mV hysteresis used in the threshold circuit
20mV hysteresis used in the threshold circuit
50mV hysteresis used in the threshold circuit
100mV hysteresis used in the threshold circuit
DAC mode used for data detection (DEFAULT)
Average mode used for data detection
Peak mode used for data detection
DAC mode used for data detection
00
01
10
11
00
01
10
11
0,1
0x0f
AUTOSLICE
2,3
9.6 Data and Clock Recovery
Data recovered in a noisy environment or from a small RF signal usually is jittery. The AMIS-52100 can remove much of that data jitter
by recovering a synchronous clock signal from the incoming data. The AMIS-52100 can be set to do auto slice data detection. The
clock and data recovery circuits can be programmed to generate a data clock for synchronously clocking the data out of the AMIS-
52100, removing much of the jitter in this process. The AMIS-52100 has an internal PLL that must be programmed to the frequency of
the data by setting the values in the FWORD register and setting the coefficients of the filter. If these values are close to the data rate,
the AMIS-52100 will recover the data clock from the incoming detected data. The CDR circuit can also be set or clamped with a
tolerance to the frequency difference between the supposed data rate and the actual data rate to improve the performance of the CDR
function. The CDR circuit can be set to reset after a programmed number of data time periods without data. This stop check function
allows the CDR circuit to reacquire the clock when new data is received, maintaining better clock to data synchronization.
Table 27 presents the registers associated with the data and clock recovery function. Refer to the AMIS application note “Clock and
Data Recovery Circuit Operation and Setup” for more information.
20
AMI Semiconductor
– Rev 4.0, Mar. 06 – M-20535-004
www.amis.com
相關PDF資料 |
PDF描述 |
|---|---|
| AMIS-52100-A | Transceiver with Clock and Data Recovery |
| AMIS-52100-I | Transceiver with Clock and Data Recovery |
| AMIS-52100-M | Transceiver with Clock and Data Recovery |
| AMIS-52150 | Low-Power Transceiver with Clock and Data Recovery |
| AMIS-53000 | Frequency Agile Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMIS52100/19293001XTD | 制造商:AMI Semiconductor 功能描述: 制造商:NTE Electronics 功能描述: |
| AMIS-52100-A | 制造商:AMI 制造商全稱:AMI 功能描述:Transceiver with Clock and Data Recovery |
| AMIS-52100-I | 制造商:AMI 制造商全稱:AMI 功能描述:Transceiver with Clock and Data Recovery |
| AMIS-52100-M | 制造商:AMI 制造商全稱:AMI 功能描述:Transceiver with Clock and Data Recovery |
| AMIS-52150 | 制造商:AMI 制造商全稱:AMI 功能描述:Low-Power Transceiver with Clock and Data Recovery |
發布緊急采購，3分鐘左右您將得到回復。