- 您現在的位置：買賣IC網 > PDF目錄366557 > AMC0XXDFLKA (Advanced Micro Devices, Inc.) 4, 8, 20, or 32 Megabyte 5.0 Volt-only Flash Memory PC Card PDF資料下載
參數資料
| 型號： | AMC0XXDFLKA |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | 4, 8, 20, or 32 Megabyte 5.0 Volt-only Flash Memory PC Card |
| 中文描述： | 4，8，20或32兆字節5.0伏，只有閃存PC卡 |
| 文件頁數： | 6/46頁 |
| 文件大小： | 157K |
| 代理商： | AMC0XXDFLKA |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
6
AmC0XXDFLKA
PIN DESCRIPTION
A0–A24
Address Inputs
These inputs are internally latched during write cycles.
All address lines should be driven.
BVD1, BVD2
Battery Voltage Detect
Internally pulled-up.
CD1, CD2
Card Detect
When card detect 1 and 2 = ground the system detects
the card.
CE1, CE2
Card Enable
This input is active low. The memory card is deselected
and power consumption is reduced to standby levels
when CE is high. CE activates the internal memory
card circuitry that controls the high and low byte control
logic of the card, input buffers segment decoders, and
associated memory devices.
D0–D15
Data Input/Output
Data inputs
are internally latched on write cycles. Data
outputs during read cycles. Data pins are active high.
When the memory card is deselected or the outputs
are disabled the outputs float to tristate.
GND
Ground
NC
No Connect
Corresponding pin is not connected.
OE
Output Enable
This input is active low and enables the data buffers
through the card outputs during read cycles.
RY/BY
This signal is output from the card and indicates the
status of the operation in progress in the card. If this
signal is low, then the card is still busy with the current
operation. Otherwise, the card is ready to accept anew
operation.
REG
Attribute Memory Select
This input is active low and enables reading the CIS
from the EEPROM.
RESET
This input to the Card is used to reset all the Flash de-
vices inside the Card to a read mode state. If you drive
or assert RESET high during a write or erase opera-
tion, then the state of the devices for the purpose of the
operation is undefined. In order to RESET, you need to
hold the RESET pin high for 500 ns, and it takes 20
before the internal circuit is RESET. When RESET is
driven high, the data bus is in a high impedance state.
V
CC
PC Card Power Supply
For device operation (5.0 V
WE
Write Enable
This input is active low and controls the write function
of the command register to the memory array. The
target address is latched on the falling edge of the WE
pulse and the appropriate data is latched on the rising
edge of the pulse.
WP
Write Protect
This output is active high and disables all Card write
operations (including writes to the attribute memory).
MEMORY CARD OPERATIONS
The D-Series Flash Memory Card is organized as an
array of individual devices. Each device is 2 Mbytes in
size with thirty-two 64K byte sectors. Although the ad-
dress space is continuous, each physical device de-
fines a logical address segment size.
μ
s
±
5%).
Erase operations can be performed on two 64KByte
sectors simultaneously. Once a memory sector or
memory segment is erased any address location may
be programmed. Flash technology allows any logical
“1” data bit to be programmed to a logical “0”. The
only way to reset bits to a logical “1” is to erase the
entire memory sector of 64K bytes or memory seg-
ment of 2 Mbytes.
Erase operations are the only operations that work on
entire memory sectors or memory segments. All other
operations such as word-wide programming are not af-
fected by the physical memory segments.
The common memory space data contents are altered
in a similar manner as writing to individual Flash mem-
ory devices. On-card address and data buffers activate
the appropriate Flash device in the memory array.
Each device internally latches address and data during
write cycles. Refer to Table 1.
Attribute memory is a separately accessed card mem-
ory space. The attribute memory space is active when
the REG pin is driven low. The Card Information Struc-
ture (CIS) describes the capabilities and specification
相關PDF資料 |
PDF描述 |
|---|---|
| AMD-640 | 64-Bit Socket 7 Interface, Integrated Write back Cache Controller, System Memory Controller, and PCI Bus Controller.(64位系統控制器(包括高速緩沖存儲器控制器，系統存儲器控制器和PCI總線控制器)) |
| AMD-645 | Peripheral Bus Controller(外圍總線控制器) |
| AMD-751 | System Bus, System Memory Controller, AGP Controller, and PCI Bus Controller(系統總線、系統存儲器控制器、AGP控制器和PCI總線控制器) |
| AMD-756 | Peripheral Bus Controller(外圍總線控制器) |
| AMD ATHLON | 32-Bit Microprocessor with 3D Multimedia Performance and Digital Video(32位微處理器帶3D多媒體性能和數字視頻) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMC-1000 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Onboard 4 GB flash and graphics controller |
| AMC-1000L7400M2G | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Onboard 4 GB flash and graphics controller |
| AMC-1000L7400M4G | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Onboard 4 GB flash and graphics controller |
| AMC102 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Two-axis precision servo controller module |
| AMC105SN0-1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROPHONE GOOSENECK |
發布緊急采購，3分鐘左右您將得到回復。