- 您現在的位置：買賣IC網 > PDF目錄362273 > AM29SL160CT-120EC x8/x16 Flash EEPROM PDF資料下載
參數資料
| 型號： | AM29SL160CT-120EC |
| 英文描述： | x8/x16 Flash EEPROM |
| 中文描述： | x8/x16閃存EEPROM |
| 文件頁數： | 25/50頁 |
| 文件大?。?/td> | 979K |
| 代理商： | AM29SL160CT-120EC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
Am29SL160C
25
After the erase operation has been suspended, the
system can read array data from or program data to
any sector not selected for erasure. (The device “erase
suspends” all sectors selected for erasure.) Normal
read and write timings and command definitions apply.
Reading at any address within erase-suspended
sectors produces status data on DQ7–DQ0. The
system can use DQ7, or DQ6 and DQ2 together, to
determine if a sector is actively erasing or is erase-sus-
pended. See “Write Operation Status” for information
on these status bits.
After an erase-suspended program operation is com-
plete, the system can once again read array data within
non-suspended sectors. The system can determine
the status of the program operation using the DQ7 or
DQ6 status bits, just as in the standard program oper-
ation. See “Write Operation Status” for more
information.
The system may also write the autoselect command
sequence when the device is in the Erase Suspend
mode. The device allows reading autoselect codes
even at addresses within erasing sectors, since the
codes are not stored in the memory array. When the
device exits the autoselect mode, the device reverts to
the Erase Suspend mode, and is ready for another
valid operation. See “Autoselect Command Sequence”
for more information.
The system must write the Erase Resume command
(address bits are “don’t care”) to exit the erase suspend
mode and continue the sector erase operation. Further
writes of the Resume command are ignored. Another
Erase Suspend command can be written after the
device has resumed erasing.
Notes:
1. See Table 12 for erase command sequence.
2.
See “DQ3: Sector Erase Timer” for more information.
Figure 4.
Erase Operation
START
Write Erase
Command Sequence
Data Poll
from System
Data = FFH
No
Yes
Erasure Completed
Embedded
Erase
algorithm
in progress
相關PDF資料 |
PDF描述 |
|---|---|
| AM29SL160CT-120EI | x8/x16 Flash EEPROM |
| AM29SL160CT-120WCC | 10MS, DBGA2, IND TEMP, GREEN, 1.8V(SERIAL EE) |
| AM29SL160CT-120WCI | x8/x16 Flash EEPROM |
| AM29SL160CT-150EC | x8/x16 Flash EEPROM |
| AM29SL160CT-150EI | 8 ULTRA THIN,MINI MAP,PB/HALO FREE,IND T(SERIAL EE) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29SL800DB120WCI | 制造商:Spansion 功能描述:FLASH PARALLEL 1.8V 8MBIT 1MX8/512KX16 120NS 48FBGA - Trays |
| AM29SL800DB90WAD | 制造商:Spansion 功能描述: |
| AM29X305ADC | 制造商:Advanced Micro Devices 功能描述:Microprocessor, 8 Bit, 50 Pin, Ceramic, DIP |
| AM2A016 | 制造商:MAG-LITE 功能描述:Bulk |
| AM2A026 | 制造商:MAG-LITE 功能描述:Bulk |
發布緊急采購，3分鐘左右您將得到回復。