- 您現在的位置：買賣IC網 > PDF目錄366516 > AM29LV64MU101RWHI (Advanced Micro Devices, Inc.) 64 Megabit (4 M x 16-Bit) MirrorBit 3.0 Volt-only Uniform Sector Flash Memory with PDF資料下載
參數資料
| 型號： | AM29LV64MU101RWHI |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | 64 Megabit (4 M x 16-Bit) MirrorBit 3.0 Volt-only Uniform Sector Flash Memory with |
| 中文描述： | 64兆位（4個M x 16位）的MirrorBit 3.0伏特，只有統一的閃存部門 |
| 文件頁數： | 29/58頁 |
| 文件大?。?/td> | 1173K |
| 代理商： | AM29LV64MU101RWHI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
28
Am29LV640MU
June 12, 2003
A D V A N C E I N F O R M A T I O N
Figure 5.
Program Operation
Program Suspend/Program Resume
Command Sequence
The Program Suspend command allows the system to
interrupt a programming operation or a Write to Buffer
programming operation so that data can be read from
any non-suspended sector. When the Program Sus-
pend command is written during a programming pro-
cess, the device halts the program operation within 15
μ
s maximum (5
μ
s typical) and updates the status bits.
Addresses are not required when writing the Program
Suspend command.
After the programming operation has been sus-
pended, the system can read array data from any
non-suspended sector. The Program Suspend com-
mand may also be issued during a programming oper-
ation while an erase is suspended. In this case, data
may be read from any addresses not in Erase Sus-
pend or Program Suspend. If a read is needed from
the SecSi Sector area (One-time Program area), then
user must use the proper command sequences to
enter and exit this region.
The system may also write the autoselect command
sequence when the device is in the Program Suspend
mode. The system can read as many autoselect
codes as required. When the device exits the autose-
lect mode, the device reverts to the Program Suspend
mode, and is ready for another valid operation. See
Autoselect Command Sequence for more information.
After the Program Resume command is written, the
device reverts to programming. The system can de-
termine the status of the program operation using the
DQ7 or DQ6 status bits, just as in the standard pro-
gram operation. See
Write Operation Status
for more
information.
The system must write the Program Resume com-
mand (address bits are don’t care) to exit the Program
Suspend mode and continue the programming opera-
tion. Further writes of the Resume command are ig-
nored. Another Program Suspend command can be
written after the device has resume programming.
START
Write Program
Command Sequence
Data Poll
from System
Verify Data
No
Yes
Last Address
No
Yes
Programming
Completed
Increment Address
Embedded
Program
algorithm
in progress
Note:
See
Table 10
for program command sequence.
相關PDF資料 |
PDF描述 |
|---|---|
| AM29LV64MU112RPCI | 64 Megabit (4 M x 16-Bit) MirrorBit 3.0 Volt-only Uniform Sector Flash Memory with |
| AM29LV64MU112RWHI | 64 Megabit (4 M x 16-Bit) MirrorBit 3.0 Volt-only Uniform Sector Flash Memory with |
| AM29LV64MU120RPCI | 64 Megabit (4 M x 16-Bit) MirrorBit 3.0 Volt-only Uniform Sector Flash Memory with |
| AM29LV64MU120RWHI | 64 Megabit (4 M x 16-Bit) MirrorBit 3.0 Volt-only Uniform Sector Flash Memory with |
| AM29LV64MU90RPCI | 64 Megabit (4 M x 16-Bit) MirrorBit 3.0 Volt-only Uniform Sector Flash Memory with |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29LV800B-120DGC1 | 制造商:Spansion 功能描述:3V 8M FLASH KNOWN GOOD DIE W/BOTTOM BOOT (COMMERCIAL TEMP) - Gel-pak, waffle pack, wafer, diced wafer on film |
| AM29LV800BB | 制造商:Advanced Micro Devices 功能描述: |
| AM29LV800BB120EC | 制造商:AMD 功能描述:* |
| AM29LV800BB-120EC | 制造商:Advanced Micro Devices 功能描述: |
| AM29LV800BB-120EI | 制造商:Advanced Micro Devices 功能描述:NOR Flash, 512K x 16, 48 Pin, Plastic, TSSOP |
發布緊急采購，3分鐘左右您將得到回復。