- 您現在的位置：買賣IC網 > PDF目錄362246 > AM29F100AT-70SC 30V Single N-Channel HEXFET Power MOSFET in a SOT-223 package; A IRLL3303 with Standard Packaging PDF資料下載
參數資料
| 型號： | AM29F100AT-70SC |
| 英文描述： | 30V Single N-Channel HEXFET Power MOSFET in a SOT-223 package; A IRLL3303 with Standard Packaging |
| 中文描述： | x8/x16閃存EEPROM |
| 文件頁數： | 15/39頁 |
| 文件大小： | 728K |
| 代理商： | AM29F100AT-70SC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
Am29F002B/Am29F002NB
15
Erase Suspend/Erase Resume Commands
The Erase Suspend command allows the system to
interrupt a sector erase operation and then read data
from, or program data to, any sector not selected for
erasure. This command is valid only during the sector
erase operation, including the 50 μs time-out period
during the sector erase command sequence. The
Erase Suspend command is ignored if written during
the chip erase operation or Embedded Program algo-
rithm. Writing the Erase Suspend command during the
Sector Erase time-out immediately terminates the
time-out period and suspends the erase operation.
Addresses are “don’t-cares” when writing the Erase
Suspend command.
When the Erase Suspend command is written during a
sector erase operation, the device requires a maximum
of 20 μs to suspend the erase operation. However,
when the Erase Suspend command is written during
the sector erase time-out, the device immediately ter-
minates the time-out period and suspends the erase
operation.
After the erase operation has been suspended, the
system can read array data from or program data to
any sector not selected for erasure. (The device “erase
suspends” all sectors selected for erasure.) Normal
read and write timings and command definitions apply.
Reading at any address within erase-suspended
sectors produces status data on DQ7–DQ0. The
system can use DQ7, or DQ6 and DQ2 together, to
determine if a sector is actively erasing or is erase-sus-
pended. See “Write Operation Status” for information
on these status bits.
After an erase-suspended program operation is com-
plete, the system can once again read array data within
non-suspended sectors. The system can determine
the status of the program operation using the DQ7 or
DQ6 status bits, just as in the standard program oper-
ation. See “Write Operation Status” for more
information.
The system may also write the autoselect command
sequence when the device is in the Erase Suspend
mode. The device allows reading autoselect codes
even at addresses within erasing sectors, since the
codes are not stored in the memory array. When the
device exits the autoselect mode, the device reverts to
the Erase Suspend mode, and is ready for another
valid operation. See “Autoselect Command Sequence”
for more information.
The system must write the Erase Resume command
(address bits are “don’t care”) to exit the erase suspend
mode and continue the sector erase operation. Further
writes of the Resume command are ignored. Another
Erase Suspend command can be written after the
device has resumed erasing.
相關PDF資料 |
PDF描述 |
|---|---|
| AM29F100AT-70SE | 30V Single N-Channel HEXFET Power MOSFET in a SOT-223 package; Similar to IRLL3303 with Lead Free Packaging |
| AM29F100AT-70SI | x8/x16 Flash EEPROM |
| AM29F100AT-90EC | 20V Single N-Channel HEXFET Power MOSFET in a TO-220AB package; A IRL3102 with Standard Packaging |
| AM29F100AT-90EE | x8/x16 Flash EEPROM |
| AM29F100AT-90EI | 100V Single N-Channel HEXFET Power MOSFET in a TO-220AB package; A IRL530N with Standard Packaging |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29F100B120EC | 制造商:AMD 功能描述:* |
| AM29F100B-120EC | 制造商:Advanced Micro Devices 功能描述: |
| AM29F100B120SC | 制造商:AMD 功能描述:New |
| AM29F100B-120SC | 制造商:Advanced Micro Devices 功能描述:NOR Flash, 64K x 16, 44 Pin, Plastic, SOP |
| AM29F100B90SIT | 制造商:AMD 功能描述:New |
發布緊急采購，3分鐘左右您將得到回復。