- 您現在的位置：買賣IC網 > PDF目錄362246 > AM29F100AT-150SI 150V Single N-Channel HEXFET Power MOSFET in a D2-Pak package; A IRFS33N15D with Tape and Reel Left Packaging PDF資料下載
參數資料
| 型號： | AM29F100AT-150SI |
| 英文描述： | 150V Single N-Channel HEXFET Power MOSFET in a D2-Pak package; A IRFS33N15D with Tape and Reel Left Packaging |
| 中文描述： | x8/x16閃存EEPROM |
| 文件頁數： | 2/39頁 |
| 文件大?。?/td> | 728K |
| 代理商： | AM29F100AT-150SI |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
2
Am29F002B/Am29F002NB
GENERAL DESCRIPTION
The Am29F002B Family consists of 2 Mbit, 5.0
volt-only Flash memory devices organized as 262,144
bytes. The Am29F002B offers the RESET# function,
the Am29F002NB does not. The data appears on
DQ7–DQ0. The device is offered in 32-pin PLCC,
32-pin TSOP, and 32-pin PDIP packages. This device
is designed to be programmed in-system with the stan-
dard system 5.0 volt V
CC
supply. No V
PP
is required for
write or erase operations. The device can also be pro-
grammed in standard EPROM programmers.
This device is manufactured using AMD’s 0.32 μm
process technology, and offers all the features and ben-
efits of the Am29F002, which was manufactured using
0.5 μm process technology.
The standard device offers access times of 55, 70, 90,
and 120 ns, allowing high speed microprocessors to
operate without wait states. To eliminate bus contention
the device has separate chip enable (CE#), write
enable (WE#) and output enable (OE#) controls.
The device requires only a
single 5.0 volt power
supply
for both read and write functions. Internally
generated and regulated voltages are provided for the
program and erase operations.
The device is entirely command set compatible with the
JEDEC single-power-supply Flash standard
. Com-
mands are written to the command register using
standard microprocessor write timings. Register con-
tents serve as input to an internal state-machine that
controls the erase and programming circuitry. Write
cycles also internally latch addresses and data needed
for the programming and erase operations. Reading
data out of the device is similar to reading from other
Flash or EPROM devices.
Device programming occurs by executing the program
command sequence. This initiates the
Embedded
Program
algorithm—an internal algorithm that auto-
matically times the program pulse widths and verifies
proper cell margin.
Device erasure occurs by executing the erase
command sequence. This initiates the
Embedded
Erase
algorithm—an internal algorithm that automati-
cally preprograms the array (if it is not already
programmed) before executing the erase operation.
During erase, the device automatically times the erase
pulse widths and verifies proper cell margin.
The host system can detect whether a program or
erase operation is complete by reading the DQ7 (Data#
Polling) and DQ6 (toggle)
status bits
. After a program
or erase cycle has been completed, the device is ready
to read array data or accept another command.
The
sector erase architecture
allows memory sectors
to be erased and reprogrammed without affecting the
data contents of other sectors. The device is fully
erased when shipped from the factory.
Hardware data protection
measures include a low VCC
detector that automatically inhibits write operations during
power transitions. The
hardware sector protection
feature disables both program and erase operations in
any combination of the sectors of memory. This can be
achieved via programming equipment.
The
Erase Suspend
feature enables the user to put
erase on hold for any period of time to read data from,
or program data to, any sector that is not selected for
erasure. True background erase can thus be achieved.
The
hardware RESET# pin
terminates any operation
in progress and resets the internal state machine to
reading array data. The RESET# pin may be tied to the
system reset circuitry. A system reset would thus also
reset the device, enabling the system microprocessor
to read the boot-up firmware from the Flash memory.
(This feature is not available on the Am29F002NB.)
The system can place the device into the
standby mode
.
Power consumption is greatly reduced in this mode.
AMD’s Flash technology combines years of Flash
memory manufacturing experience to produce the
highest levels of quality, reliability and cost effectiveness.
The device electrically erases all bits within a sector
simultaneously via Fowler-Nordheim tunneling. The
data is programmed using hot electron injection.
相關PDF資料 |
PDF描述 |
|---|---|
| AM29F100AT-70EC | x8/x16 Flash EEPROM |
| AM29F100AT-70EE | A 30V Single N-Channel HEXFET Power MOSFET in a DirectFET SQ package rated at 55 amperes optimized with low on resistance for applications such as active OR'ing. Shipped in Tape and Reel only. Part is not available in bulk, TR is implied in part number.; A IRF6621 with Standard Tape and Reel Quantity of 4800 |
| AM29F100AT-70EI | x8/x16 Flash EEPROM |
| AM29F100AT-70FC | x8/x16 Flash EEPROM |
| AM29F100AT-70FE | 30V Single N-Channel HEXFET Power MOSFET in a TO-220 FullPak (Iso) package; Similar to IRLI3803 with Lead Free Packaging |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29F100B120EC | 制造商:AMD 功能描述:* |
| AM29F100B-120EC | 制造商:Advanced Micro Devices 功能描述: |
| AM29F100B120SC | 制造商:AMD 功能描述:New |
| AM29F100B-120SC | 制造商:Advanced Micro Devices 功能描述:NOR Flash, 64K x 16, 44 Pin, Plastic, SOP |
| AM29F100B90SIT | 制造商:AMD 功能描述:New |
發布緊急采購，3分鐘左右您將得到回復。