- 您現在的位置：買賣IC網 > PDF目錄223346 > AM29BDD160GT54DPBE (ADVANCED MICRO DEVICES INC) 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory PDF資料下載
參數資料
| 型號： | AM29BDD160GT54DPBE |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | PROM |
| 英文描述： | 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory |
| 中文描述： | 512K X 32 FLASH 2.7V PROM, 54 ns, PBGA80 |
| 封裝： | 13 X 11 MM, 1 MM PITCH, BGA-80 |
| 文件頁數： | 9/80頁 |
| 文件大?。?/td> | 3476K |
| 代理商： | AM29BDD160GT54DPBE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
Am29BDD160G
15
Caution: entering the standby mode via the RE-
SET# pin also resets the device to the read mode
and floats the data I/O pins. Furthermore, entering
I
CC7 during a program or erase operation will leave
erroneous data in the address locations being oper-
ated on at the time of the RESET# pulse. These
locations require updating after the device resumes
standard operations. Refer to the “RESET#: Hard-
ware Reset Pin” section for further discussion of the
RESET# pin and its functions
.
RESET#: Hardware Reset Pin
The RESET# pin is an active low signal that is used
to reset the device under any circumstances. A logic
“0” on this pin forces the device out of any mode
that is currently executing back to the reset state.
The RESET# pin may be tied to the system reset cir-
cuitry. A system reset would thus also reset the
device. To avoid a potential bus contention during a
system reset, the device is isolated from the DQ data
bus by tri-stating the data output pins for the dura-
tion of the RESET pulse. All pins are “don’t care”
during the reset operation.
If RESET# is asserted during a program or erase op-
eration, the RY/BY# pin remains low until the reset
operation is internally complete. This action requires
between 1 s and 7s for either Chip Erase or Sector
Erase. The RY/BY# pin can be used to determine
when the reset operation is complete. Otherwise,
allow for the maximum reset time of 11 s. If RE-
SET# is asserted when a program or erase operation
is not executing (RY/BY# = “1”), the reset operation
will complete within 500 ns. Since the Am29BDD160
is a Simultaneous Operation device the user may
read a bank after 500 ns if the bank was in the read/
reset mode at the time RESET# was asserted. If one
of the banks was in the middle of either a program or
erase operation when RESET# was asserted, the
user must wait 11 s before accessing that bank.
Asserting RESET# during a program or erase opera-
tion leaves erroneous data stored in the address
locations being operated on at the time of device re-
set. These locations need updating after the reset
operation is complete. See Figure 19 for timing spec-
ifications.
Asserting RESET# active during V
CC a nd VIO power-
up is required to guarantee proper device initializa-
tion until V
CC and VIO have reached their steady
state voltages.
Output Disable Mode
See Table 1 Device Bus Operation for OE# Operation
in Output Disable Mode.
Autoselect Mode
The autoselect mode provides manufacturer and de-
vice identification, and sector protection verification,
through identifier codes output on DQ7–DQ0. This
mode is primarily intended for programming equip-
ment to automatically match a device to be
programmed with its corresponding programming al-
gorithm. However, the autoselect codes can also be
accessed in-system through the command register.
When using programming equipment, the au-
toselect mode requires V
ID on address pin A9.
Address pins A6, A1, and A0 must be as shown
in Table 12 (top boot devices) or Table 13 (bot-
tom boot devices). In addition, when verifying
sector protection, the sector address must ap-
pear on the appropriate highest order address
bits (see Tables 11 and 12). See Table 5 shows
the remaining address bits that are don’t care.
When all necessary bits have been set as re-
quired, the programming equipment may then
read the corresponding identifier code on DQ7–
DQ0.
To access the autoselect codes in-system, the
host system can issue the autoselect command
via the command. This method does not re-
quire V
ID. S ee “C om m a nd D e f i n i t i on s” for
details on using the autoselect mode.
相關PDF資料 |
PDF描述 |
|---|---|
| AM29BDD160GT65AKE | 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory |
| AM29BDD160GT65AKF | 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory |
| AM29BDD160GT65AKI | 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory |
| AM29BDD160GT65AKK | 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory |
| AM29BDD160GT65APBE | 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29BDS128HE9VKI | 制造商:Advanced Micro Devices 功能描述:Flash Mem Parallel/Serial 1.8V 128M-Bit 8M x 16 50ns 80-Pin FBGA |
| AM29BDS643GT5KVAI | 制造商:Spansion 功能描述:FLASH PARALLEL 1.8V 64MBIT 4MX16 55NS 44FBGA - Trays |
| AM29BL802CB-65RZET | 制造商:Spansion 功能描述: |
| AM29C01WW WAF | 制造商:Advanced Micro Devices 功能描述: |
| AM29C10API | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。