- 您現在的位置：買賣IC網 > PDF目錄22040 > AGLN010V2-QNG48 (Microsemi SoC)IC FPGA 10K 1.2-1.5V 48QFN PDF資料下載
參數資料
| 型號： | AGLN010V2-QNG48 |
| 廠商： | Microsemi SoC |
| 文件頁數： | 9/150頁 |
| 文件大小： | 0K |
| 描述： | IC FPGA 10K 1.2-1.5V 48QFN |
| 標準包裝： | 260 |
| 系列： | IGLOO nano |
| 邏輯元件/單元數： | 260 |
| 輸入/輸出數： | 34 |
| 門數： | 10000 |
| 電源電壓： | 1.14 V ~ 1.575 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | -20°C ~ 70°C |
| 封裝/外殼： | 48-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 48-QFN（6x6） |
| 其它名稱： | 1100-1121 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁
Pin Descriptions
3-2
Revision 17
interface is neither used nor planned for use, the VJTAG pin together with the TRST pin could be tied to
GND. It should be noted that VCC is required to be powered for JTAG operation; VJTAG alone is
insufficient. If a device is in a JTAG chain of interconnected boards, the board containing the device can
be powered down, provided both VJTAG and VCC to the part remain powered; otherwise, JTAG signals
will not be able to transition the device, even in bypass mode.
Microsemi recommends that VPUMP and VJTAG power supplies be kept separate with independent
filtering capacitors rather than supplying them from a common rail.
VPUMP
Programming Supply Voltage
IGLOO nano devices support single-voltage ISP of the configuration flash and FlashROM. For
programming, VPUMP should be 3.3 V nominal. During normal device operation, VPUMP can be left
floating or can be tied (pulled up) to any voltage between 0 V and the VPUMP maximum. Programming
power supply voltage (VPUMP) range is listed in the datasheet.
When the VPUMP pin is tied to ground, it will shut off the charge pump circuitry, resulting in no sources of
oscillation from the charge pump circuitry.
For proper programming, 0.01 F and 0.33 F capacitors (both rated at 16 V) are to be connected in
parallel across VPUMP and GND, and positioned as close to the FPGA pins as possible.
Microsemi recommends that VPUMP and VJTAG power supplies be kept separate with independent
filtering capacitors rather than supplying them from a common rail.
User Pins
I/O
User Input/Output
The I/O pin functions as an input, output, tristate, or bidirectional buffer. Input and output signal levels are
compatible with the I/O standard selected.
During programming, I/Os become tristated and weakly pulled up to VCCI. With VCCI, VMV, and VCC
supplies continuously powered up, when the device transitions from programming to operating mode, the
I/Os are instantly configured to the desired user configuration.
Unused I/Os are configured as follows:
Output buffer is disabled (with tristate value of high impedance)
Input buffer is disabled (with tristate value of high impedance)
Weak pull-up is programmed
GL
Globals
GL I/Os have access to certain clock conditioning circuitry (and the PLL) and/or have direct access to the
global network (spines). Additionally, the global I/Os can be used as regular I/Os, since they have
identical capabilities. Unused GL pins are configured as inputs with pull-up resistors.
See more detailed descriptions of global I/O connectivity in the "Clock Conditioning Circuits in IGLOO
and ProASIC3 Devices" chapter in the IGLOO nano FPGA Fabric User’s Guide. All inputs labeled
GC/GF are direct inputs into the quadrant clocks. For example, if GAA0 is used for an input, GAA1 and
GAA2 are no longer available for input to the quadrant globals. All inputs labeled GC/GF are direct inputs
into the chip-level globals, and the rest are connected to the quadrant globals. The inputs to the global
network are multiplexed, and only one input can be used as a global input.
Refer to the "I/O Structures in nano Devices" chapter of the IGLOO nano FPGA Fabric User’s Guide for
an explanation of the naming of global pins.
FF
Flash*Freeze Mode Activation Pin
Flash*Freeze is available on IGLOO nano devices. The FF pin is a dedicated input pin used to enter and
exit Flash*Freeze mode. The FF pin is active low, has the same characteristics as a single-ended I/O,
and must meet the maximum rise and fall times. When Flash*Freeze mode is not used in the design, the
FF pin is available as a regular I/O.
When Flash*Freeze mode is used, the FF pin must not be left floating to avoid accidentally entering
Flash*Freeze mode. While in Flash*Freeze mode, the Flash*Freeze pin should be constantly asserted.
The Flash*Freeze pin can be used with any single-ended I/O standard supported by the I/O bank in
which the pin is located, and input signal levels compatible with the I/O standard selected. The FF pin
相關PDF資料 |
PDF描述 |
|---|---|
| RYM43DRST | CONN EDGECARD 86POS DIP .156 SLD |
| ADM1021ARQ-REEL7 | IC SENSOR TEMP DUAL3/5.5V 16QSOP |
| A3P030-QNG48 | IC FPGA 256MAC 81I/O 48QFN |
| AGLN010V5-UCG36 | IC FPGA 10K 1.5V UCG36 |
| ADM1021ARQ-REEL | IC SENSOR TEMP DUAL3/5.5V 16QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AGLN010V2-QNG48I | 功能描述:IC FPGA NANO 1KB 10K 48-QFN RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:IGLOO nano 標準包裝:152 系列:IGLOO PLUS LAB/CLB數:- 邏輯元件/單元數:792 RAM 位總計:- 輸入/輸出數:120 門數:30000 電源電壓:1.14 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C 封裝/外殼:289-TFBGA，CSBGA 供應商設備封裝:289-CSP（14x14） |
| AGLN010V2-UCG36 | 功能描述:IC FPGA 10K 1.2-1.5V 36UCG RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:IGLOO nano 產品變化通告:XC4000(E,L) Discontinuation 01/April/2002 標準包裝:24 系列:XC4000E/X LAB/CLB數:100 邏輯元件/單元數:238 RAM 位總計:3200 輸入/輸出數:80 門數:3000 電源電壓:4.5 V ~ 5.5 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 100°C 封裝/外殼:120-BCBGA 供應商設備封裝:120-CPGA（34.55x34.55） |
| AGLN010V2-UCG36I | 功能描述:IC FPGA NANO 1KB 10K 36-UCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:IGLOO nano 標準包裝:152 系列:IGLOO PLUS LAB/CLB數:- 邏輯元件/單元數:792 RAM 位總計:- 輸入/輸出數:120 門數:30000 電源電壓:1.14 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C 封裝/外殼:289-TFBGA，CSBGA 供應商設備封裝:289-CSP（14x14） |
| AGLN010V5-QNG48 | 功能描述:IC FPGA NANO 1KB 10K 48-QFN RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:IGLOO nano 標準包裝:152 系列:IGLOO PLUS LAB/CLB數:- 邏輯元件/單元數:792 RAM 位總計:- 輸入/輸出數:120 門數:30000 電源電壓:1.14 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C 封裝/外殼:289-TFBGA，CSBGA 供應商設備封裝:289-CSP（14x14） |
| AGLN010V5-QNG48I | 功能描述:IC FPGA NANO 1KB 10K 48-QFN RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:IGLOO nano 標準包裝:152 系列:IGLOO PLUS LAB/CLB數:- 邏輯元件/單元數:792 RAM 位總計:- 輸入/輸出數:120 門數:30000 電源電壓:1.14 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C 封裝/外殼:289-TFBGA，CSBGA 供應商設備封裝:289-CSP（14x14） |
發布緊急采購，3分鐘左右您將得到回復。