參數資料
型號： ADV7181BST
廠商： ANALOG DEVICES INC
元件分類： 顏色信號轉換
英文描述： Multiformat SDTV Video Decoder
中文描述： COLOR SIGNAL DECODER, PQFP64
封裝： LEAD FREE, MS-026BCD, LQFP-64
文件頁數： 46/96頁
文件大小： 873K
代理商： ADV7181BST
ADV7181B
VBI DATA DECODE
The following low data rate VBI signals can be decoded by the
ADV7181B:
Rev. 0 | Page 46 of 96
Wide screen signaling (WSS)
Copy generation management systems (CGMS)
Closed captioning (CCAP)
EDTV
Gemstar 1×- and 2×-compatible data recovery
The presence of any of the above signals is detected and, if
applicable, a parity check is performed. The result of this testing
is contained in a confidence bit in the VBI Info[7:0] register.
Users are encouraged to first examine the VBI Info register
before reading the corresponding data registers. All VBI data
decode bits are read-only.
All VBI data registers are double-buffered with the field signals.
This means that data is extracted from the video lines and
appears in the appropriate I
2
C registers with the next field
transition. They are then static until the next field.
The user should start an I
2
C read sequence with VS by first
examining the VBI Info register. Then, depending on what data
was detected, the appropriate data registers should be read.
The data registers are filled with decoded VBI data even if their
corresponding detection bits are low; it is likely that bits within
the decoded data stream are wrong.
The closed captioning data (CCAP) is available in the I
2
C
registers, and is also inserted into the output video data stream
during horizontal blanking.
The Gemstar-compatible data is not available in the I
2
C
registers, and is inserted into the data stream only during
horizontal blanking.
WSSD Wide Screen Signaling Detected, Address 0x90 [0]
Logic 1 for this bit indicates that the data in the WSS1 and
WSS2 registers is valid.
The WSSD bit goes high if the rising edge of the start bit is
detected within a time window, and if the polarity of the parity
bit matches the transmitted data.
When WSSD is 0, no WSS is detected and confidence in the
decoded data is low.
When WSSD is 1, WSS is detected and confidence in the
decoded data is high.
CCAPD Closed Caption Detected, Address 0x90 [1]
Logic 1 for this bit indicates that the data in the CCAP1 and
CCAP2 registers is valid.
The CCAPD bit goes high if the rising edge of the start bit is
detected within a time window, and if the polarity of the parity
bit matches the transmitted data.
When CCAPD is 0, no CCAP signals are detected and
confidence in the decoded data is low.
When CCAPD is 1, the CCAP sequence is detected and
confidence in the decoded data is high.
EDTVD EDTV Sequence Detected, Address 0x90 [2]
Logic 1 for this bit indicates that the data in the EDTV1, 2, 3
registers is valid.
The EDTVD bit goes high if the rising edge of the start bit is
detected within a time window, and if the polarity of the parity
bit matches the transmitted data.
When EDTVD is 0, no EDTV sequence is detected. Confidence
in decoded data is low.
When EDTVD is 1, an EDTV sequence is detected. Confidence
in decoded data is high.
CGMSD CGMS-A Sequence Detected, Address 0x90 [3]
Logic 1 for this bit indicates that the data in the CGMS1, 2, 3
registers is valid. The CGMSD bit goes high if a valid CRC
checksum has been calculated from a received CGMS packet.
When CGMSD is 0, no CGMS transmission is detected and
confidence in decoded data is low.
When CGMSD is 1, the CGMS sequence is decoded and
confidence in decoded data is high.
CRC_ENABLE CRC CGMS-A Sequence, Address 0xB2 [2]
For certain video sources, the CRC data bits may have an
invalid format. In such circumstances, the CRC checksum
validation procedure can be disabled. The CGMSD bit goes
high if the rising edge of the start bit is detected within a time
window.
When CRC_ENABLE is 0, no CRC check is performed. The
CGMSD bit goes high if the rising edge of the start bit is
detected within a time window.
When CRC_ENABLE is 1 (default), CRC checksum is used to
validate the CGMS sequence. The CGMSD bit goes high for a
valid checksum. ADI recommended setting.
相關PDF資料
PDF描述
ADV7183B Multiformat SDTV Video Decoder
ADV7183BBSTZ Multiformat SDTV Video Decoder
ADV7183BKSTZ Multiformat SDTV Video Decoder
ADV7183KST Advanced Video Decoder with 10-Bit ADC and Component Input Support
AD7183 Advanced Video Decoder with 10-Bit ADC and Component Input Support
相關代理商/技術參數
參數描述
ADV7181C 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, Integrated, Multiformat SDTV Video Decoder and RGB Graphics Digitizer
ADV7181CBCPZ 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
ADV7181CBCPZ-REEL 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, Integrated, Multiformat SDTV Video Decoder and RGB Graphics Digitizer
ADV7181CBSTZ 功能描述:IC VIDEO DECODER SDTV RGB 64LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 編碼器，解碼器，轉換器 系列:- 產品變化通告:Development Systems Discontinuation 26/Apr/2011 標準包裝:1 系列:- 類型:編碼器 應用:DVB-S.2 系統 電壓 - 電源，模擬:- 電壓 - 電源，數字:- 安裝類型:- 封裝/外殼:模塊 供應商設備封裝:模塊 包裝:散裝 其它名稱:Q4645799
ADV7181CBSTZ-REEL 功能描述:IC VIDEO DECODER SDTV RGB 64LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 編碼器，解碼器，轉換器 系列:- 產品變化通告:Development Systems Discontinuation 26/Apr/2011 標準包裝:1 系列:- 類型:編碼器 應用:DVB-S.2 系統 電壓 - 電源，模擬:- 電壓 - 電源，數字:- 安裝類型:- 封裝/外殼:模塊 供應商設備封裝:模塊 包裝:散裝 其它名稱:Q4645799
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*