參數資料
型號： ADUC812BS
廠商： ANALOG DEVICES INC
元件分類： 微控制器/微處理器
英文描述： Circular Connector; No. of Contacts:37; Series:LJT07R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:25; Circular Contact Gender:Socket; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:25-37
中文描述： 8-BIT, FLASH, 11.0592 MHz, MICROCONTROLLER, PQFP52
封裝： MQFP-52
文件頁數： 10/31頁
文件大?。?/td> 543K
代理商： ADUC812BS
REV. 0
ADuC812
–
10
–
ADCCON3 – (ADC Control SFR #3)
The ADCCON3 register gives user software an indication of
ADC busy status.
SFR Address:
SFR Power On Default Value:
Bit Addressable:
F5H
00H
NO
BUSY RSVD RSVD RSVD CTYP CAL1 CAL0 CALST
Table III. ADCCON3 SFR Bit Designations
Bit
Location
Bit
Mnemonic Description
ADCCON3.7
BUSY
The ADC busy status bit (BUSY)
is a read-only status bit that is set
during a valid ADC conversion or
calibration cycle. Busy is auto-
matically cleared by the core at the
end of conversion or calibration.
ADCCON3.0–3.6 are reserved
(RSVD) for internal use. These
bits will read as zero and should
only be written as zero by user
software.
ADCCON3.6
ADCCON3.5
ADCCON3.4
ADCCON3.3
ADCCON3.2
ADCCON3.1
ADCCON3.0
RSVD
RSVD
RSVD
RSVD
RSVD
RSVD
RSVD
ADC Internal Reference
If the internal reference is being used, both the V
REF
and C
REF
pins should be decoupled with 100 nF capacitors to AGND.
These decoupling capacitors should be placed very close to the
V
REF
and C
REF
pins. For specified performance, it is recom-
mended that when using an external reference, this reference
should be between 2.3 V and the analog supply AV
DD
.
If the internal reference is required for use external to the
MicroConverter, it should be buffered at the V
REF
pin and a
100 nF capacitor should be connected from this pin to AGND.
The internal 2.5 V is factory calibrated to an absolute accuracy
of 2.5 V
±
50 mV. It should also be noted that the internal V
REF
will remain powered down until either of the DACs or the ADC
peripheral blocks are powered on by their respective enable bits.
Calibration
The ADC block also has four associated calibration SFRs.
These SFR’s drive calibration logic ensuring optimum perfor-
mance from the 12-bit ADC at all times. As part of the power-
on reset configuration, these SFRs are configured automatically
and transparently from factory programmed calibration con-
stants. In many applications use of factory programmed calibra-
tion constants will suffice; however, these calibration SFRs may
be overwritten by user code to further compensate for system-
dependent offset and gain errors.
Calibration Overview
The ADC block incorporates calibration hardware that ensures
optimum performance from the ADC at all times. The calibra-
tion modes are exercised as part of the ADuC812 internal factory
final test routines. The factory calibration results are stored in
Flash memory and are automatically downloaded on any power-
on-reset event to initialize the ADC calibration registers. In
ADCCON2 – (ADC Control SFR #2)
The ADCCON2 register controls ADC channel selection and
conversion modes as detailed below.
SFR Address:
SFR Power On Default Value:
Bit Addressable:
D8H
00H
YES
ADCI DMA CCONV SCONV
CS3
CS2
CS1 CS0
Table II. ADCCON2 SFR Bit Designations
Bit
Location
Bit
Mnemonic Description
ADCCON2.7
ADCI
The ADC interrupt bit (ADCI) is
set by hardware at the end of a
single ADC conversion cycle or at
the end of a DMA block conver-
sion. ADCI is cleared by hardware
when the PC vectors to the ADC
Interrupt Service Routine.
The DMA mode enable bit (DMA)
is set by the user to initiate a pre-
configured ADC DMA mode opera-
tion. A more detailed description of
this mode is given below.
The continuous conversion bit
(CCONV) is set by the user to
initiate the ADC into a continuous
mode of conversion. In this mode
the ADC starts converting based on
the timing and channel configura-
tion already set up in the ADCCON
SFRs, the ADC automatically starts
an other conversion once a previous
conversion cycle has completed.
The single conversion bit
(SCONV) is set by the user to
initiate a single conversion cycle.
The SCONV bit is automatically
reset to “0” on completion of the
single conversion cycle.
The channel selection bits (CS3-0)
allow the user to program the
ADC channel selection under
software control. Once a conver-
sion is initiated the channel
converted will be that pointed to
by these channel selection bits. In
DMA mode the channel selection
is derived from the channel ID
written to the external memory.
CS3 CS2 CS1 CS0 CH#
0
0
0
0
0
0
0
1
0
0
1
0
0
0
1
1
0
1
0
0
0
1
0
1
0
1
1
0
0
1
1
1
1
0
0
0
1
X
X
X
ADCCON2.6
DMA
ADCCON2.5
CCONV
ADCCON2.4
SCONV
ADCCON2.3
ADCCON2.2
ADCCON2.1
ADCCON2.0
CS3
CS2
CS1
CS0
0
1
2
3
4
5
6
7
Temp Sensor
Other
Combinations
DMA STOP
1
1
1
1
相關PDF資料
PDF描述
ADUC832 MicroConverter, 12-Bit ADCs and DACs with Embedded 62 kBytes Flash MCU
ADUC832BCP MicroConverter, 12-Bit ADCs and DACs with Embedded 62 kBytes Flash MCU
ADUC832BS MicroConverter, 12-Bit ADCs and DACs with Embedded 62 kBytes Flash MCU
ADUC834 MicroConverter, Dual 16-/24- Bit ADCs with Embedded 62KB FLASH MCU
ADUC834BS MicroConverter, Dual 16-/24- Bit ADCs with Embedded 62KB FLASH MCU
相關代理商/技術參數
參數描述
ADUC812BS 制造商:Analog Devices 功能描述:12-BIT ADC WITH EMBEDDED
aduc812bs-01 制造商:Analog Devices 功能描述:
ADUC812BS-REEL 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 52-Pin MQFP T/R
ADUC812BSZ 功能描述:IC ADC 12BIT MULTICH MCU 52-MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
ADUC812BSZ-01 制造商:Analog Devices 功能描述:12-BIT ADC WITH EMBEDDED MCU I.C.
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*