參數資料
型號： ADUC7032BSTZ-88
廠商： Analog Devices Inc
文件頁數： 113/120頁
文件大小： 0K
描述： IC MCU 96K FLASH DUAL 48LQFP
標準包裝： 1
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 20.48MHz
連通性： LIN，SPI，UART/USART
外圍設備： POR，PSM，溫度傳感器，WDT
輸入/輸出數： 9
程序存儲器容量： 96KB（48K x 16）
程序存儲器類型： 閃存
RAM 容量： 1.5K x 32
電壓 - 電源 (Vcc/Vdd)： 3.5 V ~ 18 V
數據轉換器： A/D 2x16b
振蕩器型： 內部
工作溫度： -40°C ~ 105°C
封裝/外殼： 48-LQFP
包裝： 托盤
ADuC7032-8L
Rev. A | Page 92 of 120
High Voltage Configuration1 Register
Name:
HVCFG1
Address:
Indirectly addressed via the HVCON high voltage interface
Default Value:
0x00
Access:
Read/write
Function:
This 8-bit register controls the function of high voltage circuits on the ADuC7032-8L. This register is not an MMR and does
not appear in the MMR memory map. It is accessed via the HVCON registered interface. Data to be written to this register is loaded via
HVDAT, and data is read back from this register via HVDAT.
Table 75. HVCFG1 Bit Designations
Bit
Description
7
Attenuator Enable Bit.
0 = disable the internal voltage attenuator and attenuator buffer.
1 = enable the internal voltage attenuator and attenuator buffer.
6
High Voltage Temperature Monitor. The high voltage temperature monitor is an uncalibrated temperature monitor located on-chip
close to the high voltage circuits. This monitor is completely separate from the on-chip, precision temperature sensor (controlled via
ADC2CON[7:6]) and allows user code to monitor die temperature change close to the hottest part of the ADuC7032-8L die. The
monitor generates a typical output voltage of 600 mV at 25°C and typically has a negative temperature coefficient of 2.1 mV/°C.
1 = enable the on-chip, high voltage temperature monitor. Once enabled, this voltage output temperature monitor is routed
directly to the temperature channel ADC.
0 = disable the on-chip, high voltage temperature monitor.
5
Voltage Channel Short Enable Bit.
1 = enable an internal short (at the attenuator, before ADC input buffer) on the voltage channel ADC and allow noise to be
measured as a self-diagnostic test.
0 = disable an internal short on the voltage channel.
4
WU Readback Enable Bit.
0 = disable input capability on the external WU pin.
1 = enable input capability on the external WU pin. In this mode, a rising or falling edge transition on the WU pin generates a high
voltage interrupt. Once this bit is set, the state of the WU pin can be monitored via the HVMON register (HVMON[7]).
3
High Voltage I/O Enable Bit.
1 = re-enable any high voltage I/O pins (LIN/WU) that have been disabled as a result of a short-circuit current event (event must last
longer than 20 μs for the LIN pin and 400 μs for the WU pin). This bit must also be set to 1 to re-enable the WU pin, if disabled by a
thermal event. It should be noted that this bit must be set to clear any pending interrupt generated by the short-circuit event (even
if the event has passed), as well as re-enabling the high voltage I/O pins.
2
Enable/Disable Short-Circuit Protection (LIN).
1 = enable passive short-circuit protection on the LIN pin. In this mode, a short-circuit event on the LIN pin generates a high voltage
interrupt, IRQ3 (if enabled in IRQEN[16]), and asserts the appropriate status bit in HVSTA but does not disable the short-circuiting pin.
0 = enable active short-circuit protection on the LIN pin. In this mode, a short-circuit event causes the LIN pin to generate a high
voltage interrupt (IRQ3), assert IRQSTA[16], and automatically disable the short-circuiting pin. Once disabled, the I/O pin can be
re-enabled only by writing to HVCFG1[3].
1
WU Pin Timeout (Monoflop) Counter Enable/Disable.
1 = disable the WU I/O timeout counter.
0 = enable a timeout counter that automatically deasserts the WU pin 1.3 seconds after user code has asserted the WU pin via
HVCFG0[4].
0
WU Open Circuit Diagnostic Enable.
1 = enable an internal WU I/O diagnostic pull-up resistor to the VDD pin, allowing detection of an open-circuit condition on the WU pin.
0 = disable an internal WU I/O diagnostic pull-up resistor.
相關PDF資料
PDF描述
ADUC7032BSTZ-8V-RL IC BATTERY SENSOR PREC 48-LQFP
ADUC7034BCPZ IC MCU FLASH 32K ANLG IO 48LFCSP
ADUC7036CCPZ IC MCU 96K FLASH DUAL 48LFCSP
ADUC7039BCP6Z-RL IC MCU ARM7 BATT SENSER 32LFCSP
ADUC7061BCPZ32 IC MCU 16/32BIT 32KB 32LFCSP
相關代理商/技術參數
參數描述
ADUC7032BSTZ-88-RL 功能描述:IC MCU 96K FLASH DUAL 48LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7032BSTZ-8L 制造商:Analog Devices 功能描述:FLASH 96K ARM7 TRIPLE 16-BIT ADC LIN IC. - Trays
ADUC7032BSTZ-8L-RL 制造商:Analog Devices 功能描述:FLASH 96K ARM7 TRIPLE 16-BIT ADC LIN IC. - Tape and Reel
ADUC7032BSTZ-8V 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述:
ADUC7032BSTZ-8V-RL 功能描述:IC BATTERY SENSOR PREC 48-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:1,500 系列:AVR® ATtiny 核心處理器:AVR 芯體尺寸:8-位 速度:16MHz 連通性:I²C，LIN，SPI，UART/USART，USI 外圍設備:欠壓檢測/復位，POR，PWM，溫度傳感器，WDT 輸入/輸出數:16 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:512 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*