- 您現在的位置：買賣IC網 > PDF目錄67358 > ADT7482ARMZ-RL (ON SEMICONDUCTOR) DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 2.5Cel, SQUARE, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | ADT7482ARMZ-RL |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 2.5Cel, SQUARE, SURFACE MOUNT |
| 封裝： | LEAD FREE, MO-187-BA, MSOP-10 |
| 文件頁數： | 4/24頁 |
| 文件大?。?/td> | 335K |
| 代理商： | ADT7482ARMZ-RL |
ADT7482
Rev. 1 | Page 12 of 24 | www.onsemi.com
REGISTERS
The registers in the ADT7482 are 8-bits wide. These registers
are used to store the results of remote and local temperature
measurements and high and low temperature limits and to
configure and control the device. A description of these registers
follows.
ADDRESS POINTER REGISTER
The address pointer register itself does not have, or require, an
address, as the first byte of every write operation is automatically
written to this register. The data in this first byte always contains
the address of another register on the ADT7482, which is stored
in the address pointer register. It is to this register address that
the second byte of a write operation is written to or to which a
subsequent read operation is performed.
The power-on default value of the address pointer register is
0x00. Therefore, if a read operation is performed immediately
after power-on, without first writing to the address pointer, the
address is 0x00.
CONFIGURATION REGISTERS
There are two configuration registers used to control the
operation of the ADT7482. Configuration 1 register is at
Address 0x03 for reads and Address 0x09 for writes. See Table 9
for details regarding the operation of this register. Configuration 2
Register is at Address 0x24 for both reads and writes. Setting Bit
7 of this register locks all lockable registers. The affected
registers can only be modified if the ADT7482 is powered down
and powered up again. See Table 16 for a list of the registers
affected by the lock bit.
TEMPERATURE VALUE REGISTERS
The ADT7482 has five registers to store the results of local and
remote temperature measurements. These registers can only be
written to by the ADC and can be read over the SMBus.
The local temperature value register is at Address 0x00.
The Remote 1 temperature value high byte register is at
Address 0x01; the Remote 1 low byte register is at
Address 0x10.
The Remote 2 temperature value high byte register is at
Address 0x30; the Remote 2 low byte register is at
Address 0x33.
The Remote 2 temperature values can be read from
Addresses 0x01 for the high byte and Address 0x10 for the
low byte if Bit 3 of Configuration Register 1 is set to 1.
To read the Remote 1 temperature values, set Bit 3 of
Configuration Register 1 to 0.
The power-on default for all five registers is 0x00.
Table 9. Configuration 1 Register (Read Address = 0x03, Write Address = 0x09)
Bit
Mnemonic
Description
7
Mask
Setting this bit to 1 masks all ALERTs on the ALERT pin. Default = 0 = ALERT enabled. This applies only if Pin 8 is
configured as ALERT, otherwise it has no effect.
6
Mon/STBY
Setting this bit to 1 places the ADT7482 in standby mode (that is, it suspends all temperature measurements (ADC). The
SMBus remains active and values can be written to and read from the registers. THERM and ALERT are also active in
standby mode. Changes made to the limit registers in standby mode that effect the THERM or ALERT outputs cause
these signals to be updated. Default = 0 = temperature monitoring enabled.
5
AL/TH
This bit selects the function of Pin 8. Default = 0 = ALERT. Setting this bit to 1 configures Pin 8 as THERM2 pin.
4
Reserved
Reserved for future use.
3
Remote 1
/Remote 2
Setting this bit to 1 enables Remote 2 values to be read from the Remote 1 registers. Default = 0 = Remote 1
temperature values and limits are read from these registers.
2
Temp
Range
Setting this bit to 1 enables the extended temperature measurement range (50°C to +150°C).
Default = 0 = (0°C to +127°C).
1
Mask R1
Setting this bit to 1 masks ALERTs due to the Remote 1 temperature exceeding a programmed limit. Default = 0.
0
Mask R2
Setting this bit to 1 masks ALERTs due to the Remote 2 temperature exceeding a programmed limit. Default = 0.
Table 10. Configuration 2 Register (Read/Write Address = 0x24)
Mnemonic
Description
7
Lock Bit
Setting this bit to 1 locks all lockable registers to their current values. This prevents settings from being tampered with
until the device is powered down. Default = 0.
<6:0>
Res
Reserved for future use.
相關PDF資料 |
PDF描述 |
|---|---|
| ADT7482ARMZ-U2 | DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 2.5Cel, SQUARE, SURFACE MOUNT |
| ADT7485ARMZ-REEL | DIGITAL TEMP SENSOR-SERIAL, 16BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
| ADT7485ARMZ | DIGITAL TEMP SENSOR-SERIAL, 16BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
| ADT7485ARMZ-REEL7 | DIGITAL TEMP SENSOR-SERIAL, 16BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
| ADT7486ARMZ-REEL | DIGITAL TEMP SENSOR-SERIAL, 16BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADT7482ARMZ-RL7 | 功能描述:板上安裝溫度傳感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7483A | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Channel Temperature Sensor and Over Temperature Alarm |
| ADT7483AARQZ | 功能描述:板上安裝溫度傳感器 2 TEMP DIODE MONITOR 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7483AARQZ-R7 | 功能描述:板上安裝溫度傳感器 2 TEMP DIODE MONITOR 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7483AARQZ-REEL | 功能描述:IC TEMP SENSOR/ALARM 3CH 16-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
發布緊急采購，3分鐘左右您將得到回復。